3D compaction printing of a continuous carbon fiber reinforced thermoplastic
作者： Masahito Ueda , Shun Kishimoto , Masao Yamawaki , Ryosuke Matsuzaki , Akira Todoroki
DOI: 10.1016/J.COMPOSITESA.2020.105985
关键词: Thermoplastic 、 3D printing 、 Compaction 、 Fabrication 、 Scanning electron microscope 、 Composite material 、 Fused filament fabrication 、 Bending 、 Materials science 、 Ultimate tensile strength
摘要: … In this study, a hot-compaction roller technique for 3D printing was researched to reduce … properties due to the hot-compaction roller was confirmed. Subsequently, hot-press molding …
sci-hub.st 参考文章(18)
Bin Huang, Sarat Singamneni, Raster angle mechanics in fused deposition modelling Journal of Composite Materials. ,vol. 49, pp. 363- 383 ,(2015) , 10.1177/0021998313519153
Xiaoyong Tian, Tengfei Liu, Chuncheng Yang, Qingrui Wang, Dichen Li, Interface and performance of 3D printed continuous carbon fiber reinforced PLA composites Composites Part A-applied Science and Manufacturing. ,vol. 88, pp. 198- 205 ,(2016) , 10.1016/J.COMPOSITESA.2016.05.032
Yusuke Yamanaka, Akira Todoroki, Masahito Ueda, Yoshiyasu Hirano, Ryosuke Matsuzaki, Fiber Line Optimization in Single Ply for 3D Printed Composites Open Journal of Composite Materials. ,vol. 06, pp. 121- 131 ,(2016) , 10.4236/OJCM.2016.64012
L.G. Blok, M.L. Longana, H. Yu, B.K.S. Woods, An investigation into 3D printing of fibre reinforced thermoplastic composites Additive manufacturing. ,vol. 22, pp. 176- 186 ,(2018) , 10.1016/J.ADDMA.2018.04.039
MA Caminero, JM Chacón, I García-Moreno, JM Reverte, None, Interlaminar bonding performance of 3D printed continuous fibre reinforced thermoplastic composites using fused deposition modelling Polymer Testing. ,vol. 68, pp. 415- 423 ,(2018) , 10.1016/J.POLYMERTESTING.2018.04.038
Masahito UEDA, Ryo OMURO, Shun KISHIMOTO, Ryosuke MATSUZAKI, Yoshiyasu HIRANO, Akira TODOROKI, Masao YAMAWAKI, Cutting Edge of Molding Techniques of Composite Materials: IV: 3D Printing of CFRP Journal of The Society of Materials Science, Japan. ,vol. 67, pp. 885- 888 ,(2018) , 10.2472/JSMS.67.888
Takuya Takahashi, Masahito Ueda, Keisuke Iizuka, Akinori Yoshimura, Tomohiro Yokozeki, Simulation on kink-band formation during axial compression of a unidirectional carbon fiber-reinforced plastic constructed by X-ray computed tomography images Advanced Composite Materials. ,vol. 28, pp. 347- 363 ,(2019) , 10.1080/09243046.2018.1555387
Meng Luo, Xiaoyong Tian, Junfan Shang, Weijun Zhu, Dichen Li, Yingjie Qin, Impregnation and interlayer bonding behaviours of 3D-printed continuous carbon-fiber-reinforced poly-ether-ether-ketone composites Composites Part A-applied Science and Manufacturing. ,vol. 121, pp. 130- 138 ,(2019) , 10.1016/J.COMPOSITESA.2019.03.020
Ebrahim Oromiehie, B. Gangadhara Prusty, Paul Compston, Ginu Rajan, Automated fibre placement based composite structures: Review on the defects, impacts and inspections techniques Composite Structures. ,vol. 224, pp. 110987- ,(2019) , 10.1016/J.COMPSTRUCT.2019.110987
Heather J. O'Connor, Denis P. Dowling, Low‐pressure additive manufacturing of continuous fiber‐reinforced polymer composites Polymer Composites. ,vol. 40, pp. 4329- 4339 ,(2019) , 10.1002/PC.25294