Properties of TiN–Al2O3–TiCN–TiN, TiAlN, and DLC-coated Ti(C,N)-based cermets and their wear behaviors during dry cutting of 7075 aluminum alloys
作者： Junbo Liu , Ji Xiong , Li Zhou , Zhixing Guo , Huiting Wen
DOI: 10.1111/IJAC.13656
关键词: Tin 、 Aluminium 、 Metallurgy 、 Materials science 、 Cermet
摘要:
sci-hub.st 参考文章(35)
S. Bhowmick, A. Banerji, A.T. Alpas, Tribological behavior of Al–6.5%, –12%, –18.5% Si alloys during machining using CVD diamond and DLC coated tools Surface & Coatings Technology. ,vol. 284, pp. 353- 364 ,(2015) , 10.1016/J.SURFCOAT.2015.08.073
Hui ZHANG, Neng-ping JIN, Jiang-hua CHEN, Hot deformation behavior of Al-Zn-Mg-Cu-Zr aluminum alloys during compression at elevated temperature Transactions of Nonferrous Metals Society of China. ,vol. 21, pp. 437- 442 ,(2011) , 10.1016/S1003-6326(11)60733-4
A. Ben Cheikh Larbi, B. Tlili, Fretting wear of multilayered PVD TiAlCN/TiAlN/TiAl on AISI 4140 steel Surface and Coatings Technology. ,vol. 201, pp. 1511- 1518 ,(2006) , 10.1016/J.SURFCOAT.2006.02.025
Zhikang Shen, Xinqi Yang, Zhaohua Zhang, Lei Cui, Tielong Li, Microstructure and failure mechanisms of refill friction stir spot welded 7075-T6 aluminum alloy joints Materials & Design. ,vol. 44, pp. 476- 486 ,(2013) , 10.1016/J.MATDES.2012.08.026
L.A. Dobrzański, J. Mikuła, Structure and properties of PVD and CVD coated Al2O3 + TiC mixed oxide tool ceramics for dry on high speed cutting processes Journal of Materials Processing Technology. ,vol. 164, pp. 822- 831 ,(2005) , 10.1016/J.JMATPROTEC.2005.02.089
Konstantinos-Dionysios Bouzakis, Nikolaos Michailidis, Georgios Skordaris, Emmanouil Bouzakis, Dirk Biermann, Rachid M'Saoubi, Cutting with coated tools: Coating technologies, characterization methods and performance optimization CIRP Annals. ,vol. 61, pp. 703- 723 ,(2012) , 10.1016/J.CIRP.2012.05.006
G.S. Fox-Rabinovich, A.I. Kovalev, M.H. Aguirre, B.D. Beake, K. Yamamoto, S.C. Veldhuis, J.L. Endrino, D.L. Wainstein, A.Y. Rashkovskiy, Design and performance of AlTiN and TiAlCrN PVD coatings for machining of hard to cut materials Surface & Coatings Technology. ,vol. 204, pp. 489- 496 ,(2009) , 10.1016/J.SURFCOAT.2009.08.021
Jinkwan Jung, Shinhoo Kang, Effect of ultra-fine powders on the microstructure of Ti(CN)–xWC–Ni cermets Acta Materialia. ,vol. 52, pp. 1379- 1386 ,(2004) , 10.1016/J.ACTAMAT.2003.11.021
Hao Du, Ji Xiong, Haibo Zhao, Yuemei Wu, Weicai Wan, Linlin Wang, Structure and properties of TiAlLaN films deposited at various bias voltages Applied Surface Science. ,vol. 292, pp. 688- 694 ,(2014) , 10.1016/J.APSUSC.2013.12.035
Sandro Cardoso Santos, Wisley Falco Sales, Flávio José da Silva, Sinésio Domingues Franco, Marcio Bacci da Silva, Tribological characterisation of PVD coatings for cutting tools Surface & Coatings Technology. ,vol. 184, pp. 141- 148 ,(2004) , 10.1016/J.SURFCOAT.2003.10.153