Evaluation of surface residual stresses in HVOF sprayed WC-12Co coatings by XRD and ED-hole drilling
作者： M. Jalali Azizpour , S. Nourouzi
DOI: 10.1007/S12206-013-0715-5
关键词: Coating 、 Thermal spraying 、 Stress (mechanics) 、 Residual stress 、 Scanning electron microscope 、 Hole drilling method 、 Metallurgy 、 Materials science 、 Optical microscope 、 Drilling
摘要: Thermally sprayed coatings are inherently associated with residual stresses in the coatings. These have a noticeable effect on physical and mechanical properties of The high speed hole drilling method is widely used to measure stress. Due nature thermally coatings, application this for WC/Co has some limitations. In current study, WC-12Co were deposited using HVOF thermal spraying. electro discharge was developed through thickness stress WC-Co Morphological studies conducted optical microscopy scanning electron (SEM) evaluate powder coating characteristics. sin2ψ surface by means XRD. at EDM XRD approximately −32.54 MPa −40.6 respectively. experimental results reveal that curves not uniform thickness. It been found mean −126 MPa. Obtained good agreement reported values from literatures. confirms feasibility measurement
springer.com
sci-hub.se 参考文章(19)
S Thaiwatthana, N Jantaping, P Limthongkul, Residual stress measurement of low temperature plasma surface alloyed layer using X-ray diffraction techniques Surface Engineering. ,vol. 28, pp. 273- 276 ,(2012) , 10.1179/1743294411Y.0000000060
ALBERT N. LIN, System Identification for Determination of Dynamic Properties from Forced‐Vibration Testing Experimental Techniques. ,vol. 9, pp. 34- 37 ,(1985) , 10.1111/J.1747-1567.1985.TB02364.X
J Pina, A Dias, J.L Lebrun, Study by X-ray diffraction and mechanical analysis of the residual stress generation during thermal spraying Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 347, pp. 21- 31 ,(2003) , 10.1016/S0921-5093(02)00580-4
M. T. Flaman, J. A. Herring, ULTRA-HIGH-SPEED CENTER-HOLE TECHNIQUE FOR DIFFICULT MACHINING MATERIALS Experimental Techniques. ,vol. 10, pp. 34- 35 ,(1986) , 10.1111/J.1747-1567.1986.TB01370.X
Tie-Gang Wang, Sheng-Sheng Zhao, Wei-Gang Hua, Jia-Bao Li, Jun Gong, Chao Sun, None, Estimation of residual stress and its effects on the mechanical properties of detonation gun sprayed WC–Co coatings Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 527, pp. 454- 461 ,(2010) , 10.1016/J.MSEA.2009.10.009
R.S Lima, A Kucuk, C.C Berndt, Evaluation of microhardness and elastic modulus of thermally sprayed nanostructured zirconia coatings Surface & Coatings Technology. ,vol. 135, pp. 166- 172 ,(2001) , 10.1016/S0257-8972(00)00997-X
Hwa-Teng Lee, Werner P. Rehbach, Fu-Chuan Hsu, Tzu-Yao Tai, Edward Hsu, The study of EDM hole-drilling method for measuring residual stress in SKD11 tool steel Journal of Materials Processing Technology. ,vol. 149, pp. 88- 93 ,(2004) , 10.1016/J.JMATPROTEC.2003.10.056
J. Stokes, L. Looney, Residual stress in HVOF thermally sprayed thick deposits Surface & Coatings Technology. ,vol. 177, pp. 18- 23 ,(2004) , 10.1016/J.SURFCOAT.2003.06.003
P BANSAL, P SHIPWAY, S LEEN, Residual stresses in high-velocity oxy-fuel thermally sprayed coatings – Modelling the effect of particle velocity and temperature during the spraying process Acta Materialia. ,vol. 55, pp. 5089- 5101 ,(2007) , 10.1016/J.ACTAMAT.2007.05.031
R. Ahmed, M. Hadfield, Experimental measurement of the residual stress field within thermally sprayed rolling elements Wear. ,vol. 209, pp. 84- 95 ,(1997) , 10.1016/S0043-1648(97)00009-4