Additive manufactured A357.0 samples using the laser powder bed fusion technique: Shear and tensile performance
作者： Lucia Denti
DOI: 10.3390/MET8090670
关键词: Shear (sheet metal) 、 Laser 、 Fusion 、 Composite material 、 Ultimate tensile strength 、 Powder bed 、 Materials science
摘要:
sci-hub.se 参考文章(10)
K.G. Prashanth, S. Scudino, H.J. Klauss, K.B. Surreddi, L. Löber, Z. Wang, A.K. Chaubey, U. Kühn, J. Eckert, Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 590, pp. 153- 160 ,(2014) , 10.1016/J.MSEA.2013.10.023
Wen-ming JIANG, Zi-tian FAN, De-jun LIU, Microstructure, tensile properties and fractography of A356 alloy under as-cast and T6 obtained with expendable pattern shell casting process Transactions of Nonferrous Metals Society of China. ,vol. 22, ,(2012) , 10.1016/S1003-6326(12)61676-8
T. B. Sercombe, X. Li, Selective laser melting of aluminium and aluminium metal matrix composites: review Materials Technology. ,vol. 31, pp. 77- 85 ,(2016) , 10.1179/1753555715Y.0000000078
Heng Rao, Stephanie Giet, Kun Yang, Xinhua Wu, Chris HJ Davies, None, The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting Materials & Design. ,vol. 109, pp. 334- 346 ,(2016) , 10.1016/J.MATDES.2016.07.009
J. Wu, X.Q. Wang, W. Wang, M.M. Attallah, M.H. Loretto, Microstructure and strength of selectively laser melted AlSi10Mg Acta Materialia. ,vol. 117, pp. 311- 320 ,(2016) , 10.1016/J.ACTAMAT.2016.07.012
Dirk Herzog, Vanessa Seyda, Eric Wycisk, Claus Emmelmann, Additive manufacturing of metals Acta Materialia. ,vol. 117, pp. 371- 392 ,(2016) , 10.1016/J.ACTAMAT.2016.07.019
Alberta Aversa, Massimo Lorusso, Francesco Trevisan, Elisa Ambrosio, Flaviana Calignano, Diego Manfredi, Sara Biamino, Paolo Fino, Mariangela Lombardi, Matteo Pavese, Effect of Process and Post-Process Conditions on the Mechanical Properties of an A357 Alloy Produced via Laser Powder Bed Fusion Metals. ,vol. 7, pp. 68- ,(2017) , 10.3390/MET7020068
Jeremy H. Rao, Yong Zhang, Xiya Fang, Yu Chen, Xinhua Wu, Chris H.J. Davies, The origins for tensile properties of selective laser melted aluminium alloy A357 Additive manufacturing. ,vol. 17, pp. 113- 122 ,(2017) , 10.1016/J.ADDMA.2017.08.007
Danny Van Hemelrijck, Maria Strantza, Dimitrios Angelis, Dieter De Baere, Patrick Guillaume, Additive Manufacturing: the next industrial revolution? Journal of acoustic emission. ,vol. 18, pp. 280- ,(2016)
Amir Hadadzadeh, Babak Shalchi Amirkhiz, Jian Li, Mohsen Mohammadi, Columnar to equiaxed transition during direct metal laser sintering of AlSi10Mg alloy: Effect of building direction Additive manufacturing. ,vol. 23, pp. 121- 131 ,(2018) , 10.1016/J.ADDMA.2018.08.001