Tribological behaviour of carbon and low alloy steels: effect of mechanical properties and test conditions
作者： R Autay , M Kchaou , K Elleuch , F Dammak
DOI: 10.1179/1751584X11Y.0000000022
关键词: Alloy 、 Cylinder (engine) 、 Carbon steel 、 Carbon 、 Materials science 、 Lubrication 、 Metallurgy 、 Tribology 、 Alloy steel 、 Composite material 、 Reciprocating motion
摘要: In this paper, the effects of mechanical properties and test conditions on tribological behaviour ISO C45 carbon steel 42CrMo4 low alloy were studied. The tests carried out, without lubrication, a reciprocating friction tester. Cylinder flat contact configuration was adopted. results showed that there is no obvious relationship between ones. However, variation in coefficient depends conditions. contrary to normal load, effect sliding speed not same for two nuances. are dependent, however, nature wear debris.
sci-hub.se 参考文章(14)
Mehmet Karakan, Akgün Alsaran, Ayhan Çelik, Effect of process time on structural and tribological properties of ferritic plasma nitrocarburized AISI 4140 steel Materials & Design. ,vol. 25, pp. 349- 353 ,(2004) , 10.1016/J.MATDES.2003.10.017
M.H. Kim, K.Y. Rhee, Y.N. Paik, J.S. Hong, Y.S. Ham, Experimental investigation on the mechanical behavior of high-frequency induction-hardened mild carbon, SPS5 steel Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 485, pp. 31- 38 ,(2008) , 10.1016/J.MSEA.2007.07.088
Babic Miroslav, Aleksandar Vencl, Slobodan Mitrović, Ilija Bobić, Influence of T4 Heat Treatment on Tribological Behavior of Za27 Alloy Under Lubricated Sliding Condition Tribology Letters. ,vol. 36, pp. 125- 134 ,(2009) , 10.1007/S11249-009-9467-X
Mustafa Ulutan, Osman N. Celik, Hakan Gasan, Umit Er, Effect of Different Surface Treatment Methods on the Friction and Wear Behavior of AISI 4140 Steel Journal of Materials Science & Technology. ,vol. 26, pp. 251- 257 ,(2010) , 10.1016/S1005-0302(10)60042-4
Jiangang Jia, Qin Ma, Jinjun Lu, Bo Wang, Reciprocating Sliding Friction and Wear Property of Fe3Si Based Alloys Containing Cu in Water Lubrication Tribology Letters. ,vol. 30, pp. 113- 121 ,(2008) , 10.1007/S11249-008-9318-1
A. Alsaran, F. Yildiz, A. Çelik, Effects of post-aging on wear and corrosion properties of nitrided AISI 4140 steel Surface & Coatings Technology. ,vol. 201, pp. 3147- 3154 ,(2006) , 10.1016/J.SURFCOAT.2006.06.033
G.R. Symmons, G.J. McNulty, Acoustic output from stick-slip friction☆ Wear. ,vol. 113, pp. 79- 82 ,(1986) , 10.1016/0043-1648(86)90057-8
B Podgornik, J Vižintin, V Leskovšek, Wear properties of induction hardened, conventional plasma nitrided and pulse plasma nitrided AISI 4140 steel in dry sliding conditions Wear. ,vol. 232, pp. 231- 242 ,(1999) , 10.1016/S0043-1648(99)00151-9
A. García, A. Varela, L. García, M.C. Río, S. Naya, M. Suárez, Comparing the tribological behaviour of an austenitic steel subjected to diverse thermal treatments Wear. ,vol. 258, pp. 203- 207 ,(2005) , 10.1016/J.WEAR.2004.09.003
N.Y. Sari, M. Yilmaz, Investigation of abrasive + erosive wear behaviour of surface hardening methods applied to AISI 1050 steel Materials & Design. ,vol. 27, pp. 470- 478 ,(2006) , 10.1016/J.MATDES.2004.11.020