Microstructural porosity in additive manufacturing: The formation and detection of pores in metal parts fabricated by powder bed fusion
作者： Antonella Sola , Alireza Nouri
DOI: 10.1002/AMP2.10021
关键词: Materials science 、 Porosity 、 Fusion 、 Metal 、 Composite material 、 Powder bed
摘要: … structures, the formation of pores and the development of high residual … the laser beam path.33, 34 This FE model is able to explain the formation of additional pores other than keyholes. …
sci-hub.se 
researchgate.net 参考文章(72)
Haijun Gong, Khalid Rafi, Hengfeng Gu, G.D. Janaki Ram, Thomas Starr, Brent Stucker, Influence of Defects on Mechanical Properties of Ti-6Al-4V Components Produced by Selective Laser Melting and Electron Beam Melting Materials & Design. ,vol. 86, pp. 545- 554 ,(2015) , 10.1016/J.MATDES.2015.07.147
Onome Scott-Emuakpor, Casey Holycross, Tommy George, Kevin Knapp, Joseph Beck, Fatigue and Strength Studies of Titanium 6Al–4V Fabricated by Direct Metal Laser Sintering Journal of Engineering for Gas Turbines and Power. ,vol. 138, pp. 022101- ,(2016) , 10.1115/1.4031271
Christian Weingarten, Damien Buchbinder, Norbert Pirch, Wilhelm Meiners, Konrad Wissenbach, Reinhart Poprawe, Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg Journal of Materials Processing Technology. ,vol. 221, pp. 112- 120 ,(2015) , 10.1016/J.JMATPROTEC.2015.02.013
Lore Thijs, Karolien Kempen, Jean-Pierre Kruth, Jan Van Humbeeck, Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder Acta Materialia. ,vol. 61, pp. 1809- 1819 ,(2013) , 10.1016/J.ACTAMAT.2012.11.052
S. Das, Physical Aspects of Process Control in Selective Laser Sintering of Metals Advanced Engineering Materials. ,vol. 5, pp. 701- 711 ,(2003) , 10.1002/ADEM.200310099
B. Ferrar, L. Mullen, E. Jones, R. Stamp, C.J. Sutcliffe, Gas flow effects on selective laser melting (SLM) manufacturing performance Journal of Materials Processing Technology. ,vol. 212, pp. 355- 364 ,(2012) , 10.1016/J.JMATPROTEC.2011.09.020
A.B. Spierings, M. Schneider, R. Eggenberger, Comparison of density measurement techniques for additive manufactured metallic parts Rapid Prototyping Journal. ,vol. 17, pp. 380- 386 ,(2011) , 10.1108/13552541111156504
Wayne E King, Holly D Barth, Victor M Castillo, Gilbert F Gallegos, John W Gibbs, Douglas E Hahn, Chandrika Kamath, Alexander M Rubenchik, None, Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing Journal of Materials Processing Technology. ,vol. 214, pp. 2915- 2925 ,(2014) , 10.1016/J.JMATPROTEC.2014.06.005
Manickavasagam Krishnan, Eleonora Atzeni, Riccardo Canali, Flaviana Calignano, Diego Manfredi, Elisa Paola Ambrosio, Luca Iuliano, On the effect of process parameters on properties of AlSi10Mg parts produced by DMLS Rapid Prototyping Journal. ,vol. 20, pp. 449- 458 ,(2014) , 10.1108/RPJ-03-2013-0028
Vojislav Petrovic, Juan Vicente Haro Gonzalez, Olga Jordá Ferrando, Javier Delgado Gordillo, Jose Ramón Blasco Puchades, Luis Portolés Griñan, Additive Layer Manufacturing: State of the art in industrial applications through case studies International Journal of Production Research. ,vol. 49, pp. 1061- 1079 ,(2011) , 10.1080/00207540903479786