Some studies on drilling of hybrid metal matrix composites based on Taguchi techniques
作者： S. Basavarajappa , G. Chandramohan , J. Paulo Davim
DOI: 10.1016/J.JMATPROTEC.2007.05.043
关键词: Fabrication 、 Composite number 、 Matrix (chemical analysis) 、 Composite material 、 Materials science 、 Drilling 、 Metallurgy 、 Carbide 、 Machinability 、 Surface finish 、 Metal
摘要: Abstract Drilling is a metal removal process and important for the final fabrication stage prior to application. This paper discusses influence of cutting parameters on drilling characteristics hybrid matrix composites (MMCs)—Al2219/15SiCp Al2219/15SiCp–3Gr. The are fabricated using stir casting method. Taguchi design experiments analysis variance (ANOVA) employed analyze these composites. were conducted study effect spindle speed feed rate force, surface finish burr height solid carbide multifacet drills 5 mm diameter. results reveal that dependent variables greatly influenced by rather than both ceramic–graphite reinforced composite has better machinibility those with SiCp
elsevier.com
sci-hub.se 参考文章(27)
M. El-Gallab, M. Sklad, Machining of Al/SiC particulate metal matrix composites: Part II: Workpiece surface integrity Journal of Materials Processing Technology. ,vol. 83, pp. 277- 285 ,(1998) , 10.1016/S0924-0136(98)00072-7
J.Paulo Davim, C.A Conceição António, Optimal drilling of particulate metal matrix composites based on experimental and numerical procedures International Journal of Machine Tools and Manufacture. ,vol. 41, pp. 21- 31 ,(2001) , 10.1016/S0890-6955(00)00071-7
J. Goni, I. Mitxelena, J. Coleto, Development of low cost metal matrix composites for commercial applications Materials Science and Technology. ,vol. 16, pp. 743- 746 ,(2000) , 10.1179/026708300101508739
I. A. Ibrahim, F. A. Mohamed, E. J. Lavernia, Particulate reinforced metal matrix composites — a review Journal of Materials Science. ,vol. 26, pp. 1137- 1156 ,(1991) , 10.1007/BF00544448
S. Basavarajappa, G. Chandramohan, M. Prabu, K. Mukund, M. Ashwin, Drilling of hybrid metal matrix composites : Workpiece surface integrity International Journal of Machine Tools & Manufacture. ,vol. 47, pp. 92- 96 ,(2007) , 10.1016/J.IJMACHTOOLS.2006.02.008
M. El-Gallab, M. Sklad, Machining of Al/SiC particulate metal-matrix composites Journal of Materials Processing Technology. ,vol. 83, pp. 151- 158 ,(1998) , 10.1016/S0924-0136(98)00054-5
Edith Morin, Jacques Masounave, E.E. Laufer, Effect of drill wear on cutting forces in the drilling of metal-matrix composites Wear. ,vol. 184, pp. 11- 16 ,(1995) , 10.1016/0043-1648(94)06541-1
Gül Tosun, Mehtap Muratoglu, The drilling of Al/SiCp metal–matrix composites. Part II: workpiece surface integrity Composites Science and Technology. ,vol. 64, pp. 1413- 1418 ,(2004) , 10.1016/J.COMPSCITECH.2003.07.007
W. Zhou, Z.M. Xu, Casting of SiC reinforced metal matrix composites Journal of Materials Processing Technology. ,vol. 63, pp. 358- 363 ,(1997) , 10.1016/S0924-0136(96)02647-7
J. Monaghan, P. O'Reilly, The drilling of an Al/SiC metal-matrix composite Journal of Materials Processing Technology. ,vol. 33, pp. 469- 480 ,(1992) , 10.1016/0924-0136(92)90280-6