Prediction and Analysis of Size Tolerances Achievable in Peripheral End Milling
作者： M. N. Islam , Han Ul Lee , Dong-Woo Cho
关键词: Component (UML) 、 Simulation software 、 End milling 、 Engineering 、 Mechanical engineering 、 Range (statistics) 、 Average size 、 Variable (computer science) 、 Cutting force
摘要: This paper details the current research on size tolerances of component parts machined through peripheral end milling using a prototype simulation software for virtual based previously reported cutting force and surface generation models. Firstly, was employed predicting prismatic by varying one controllable variable at time then, relationship between tolerance changed monitored. When distinct noted it verified both analytically experimentally. The results indicated that while average variation, which contributed to variation basic parts, always proportional metal removal rate, range variations not. Thus, there is scope increasing rate without sacrificing tolerances. knowledge acquired this can be applied selecting an optimum condition when are specified.Copyright © 2006 ASME
asme.org
springer.com
researchgate.net 
sci-hub.se 参考文章(16)
T.S. Ong, B.K. Hinds, The application of tool deflection knowledge in process planning to meet geometric tolerances International Journal of Machine Tools and Manufacture. ,vol. 43, pp. 731- 737 ,(2003) , 10.1016/S0890-6955(03)00027-0
Won-Soo Yun, Jeong Hoon Ko, Han Ul Lee, Dong-Woo Cho, Kornel F Ehmann, Development of a virtual machining system, part 3: cutting process simulation in transient cuts International Journal of Machine Tools and Manufacture. ,vol. 42, pp. 1617- 1626 ,(2002) , 10.1016/S0890-6955(02)00139-6
E. Budak, Analytical models for high performance milling. Part I: Cutting forces, structural deformations and tolerance integrity International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 1478- 1488 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.09.009
Philippe Dépincé, Jean-Yves Hascoët, Active integration of tool deflection effects in end milling. Part 1. Prediction of milled surfaces International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 937- 944 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.08.005
M.A. Salgado, L.N. López de Lacalle, A. Lamikiz, J. Muñoa, J.A. Sánchez, Evaluation of the stiffness chain on the deflection of end-mills under cutting forces International Journal of Machine Tools & Manufacture. ,vol. 45, pp. 727- 739 ,(2005) , 10.1016/J.IJMACHTOOLS.2004.08.023
Jeong Hoon Ko, Won-Soo Yun, Dong-Woo Cho, Kornel F. Ehmann, Development of a virtual machining system, part 1: approximation of the size effect for cutting force prediction International Journal of Machine Tools and Manufacture. ,vol. 42, pp. 1595- 1605 ,(2002) , 10.1016/S0890-6955(02)00137-2
K. Shirase, Y. Altintaş, Cutting force and dimensional surface error generation in peripheral milling with variable pitch helical end mills International Journal of Machine Tools & Manufacture. ,vol. 36, pp. 567- 584 ,(1996) , 10.1016/0890-6955(95)00063-1
Shi Hyoung Ryu, Hae Sung Lee, Chong Nam Chu, The form error prediction in side wall machining considering tool deflection International Journal of Machine Tools & Manufacture. ,vol. 43, pp. 1405- 1411 ,(2003) , 10.1016/S0890-6955(03)00183-4
Erhan Budak, Yusuf Altintas, Peripheral milling conditions for improved dimensional accuracy International Journal of Machine Tools & Manufacture. ,vol. 34, pp. 907- 918 ,(1994) , 10.1016/0890-6955(94)90024-8
L.N. López de Lacalle, A. Lamikiz, J.A. Sánchez, M.A. Salgado, Toolpath selection based on the minimum deflection cutting forces in the programming of complex surfaces milling International Journal of Machine Tools & Manufacture. ,vol. 47, pp. 388- 400 ,(2007) , 10.1016/J.IJMACHTOOLS.2006.03.010