Effect of power supply on the deposition of Zn on a steel substrate using cathodic plasma electrolysis
作者： Xu Yang , Guojian Hao , Xianfei Ding , Yongfeng Liang , Junpin Lin
DOI: 10.1016/J.SURFCOAT.2017.06.048
关键词: Metallurgy 、 Cathodic protection 、 Electrolysis 、 Zinc 、 Materials science 、 Coating 、 Carbon steel 、 Square wave 、 Duty cycle 、 Direct current 、 Composite material
摘要: Abstract Cathodic plasma electrolysis (CPE) has been used as an environmentally-friendly process to deposit metal coating on substrate. In this work, a of zinc was deposited via CPE low carbon steel wire using direct current (DC) and square wave pulsed (SWPC) power. The experimental results showed that application continuous DC power did not produce deposition, but dense easily applied the substrate with SWPC at 120 V, 4000 Hz 80% duty cycle. resulting porous some imperfections surface, morphology quality could be controlled by adjusting parameters Increasing both cycle frequency resulted in lower deposition rate, denser. surface cleaned generated Zn found accumulate during rise pulse. A linear regression model established describe relationship between thickness parameters.
sci-hub.se 参考文章(23)
Cheng Quan, Yedong He, Microstructure and characterization of a novel cobalt coating prepared by cathode plasma electrolytic deposition Applied Surface Science. ,vol. 353, pp. 1320- 1325 ,(2015) , 10.1016/J.APSUSC.2015.07.080
Peng Wang, Yedong He, Jin Zhang, Al2O3–ZrO2–Pt composite coatings prepared by cathode plasma electrolytic deposition on the TiAl alloy Surface & Coatings Technology. ,vol. 283, pp. 37- 43 ,(2015) , 10.1016/J.SURFCOAT.2015.10.050
M. Aliofkhazraei, A. Sabour Roohaghdam, A novel method for preparing aluminum diffusion coating by nanocrystalline plasma electrolysis Electrochemistry Communications. ,vol. 9, pp. 2686- 2691 ,(2007) , 10.1016/J.ELECOM.2007.09.002
Sudhir Kumar, Pradeep Kumar, HS Shan, None, Effect of evaporative pattern casting process parameters on the surface roughness of Al–7% Si alloy castings Journal of Materials Processing Technology. ,vol. 182, pp. 615- 623 ,(2007) , 10.1016/J.JMATPROTEC.2006.09.005
C.N. Panagopoulos, D.A. Lagaris, P.C. Vatista, Adhesion and corrosion behaviour of Zn–Co electrodeposits on mild steel Materials Chemistry and Physics. ,vol. 126, pp. 398- 403 ,(2011) , 10.1016/J.MATCHEMPHYS.2010.10.049
Jie Wu, Wenbin Xue, Xiaoyue Jin, Bin Wang, Jiancheng Du, Zhenglong Wu, Preparation and characterization of diamond-like carbon/oxides composite film on carbon steel by cathodic plasma electrolysis Applied Physics Letters. ,vol. 103, pp. 031905- ,(2013) , 10.1063/1.4813830
A.L. Yerokhin, X. Nie, A. Leyland, A. Matthews, S.J. Dowey, Plasma electrolysis for surface engineering Surface and Coatings Technology. ,vol. 122, pp. 73- 93 ,(1999) , 10.1016/S0257-8972(99)00441-7
Guanghong Zhao, Yedong He, Plasma electroplating Ni coating on pure copper sheet—the effects of H2SO4 concentration on the microstructure and mechanical properties Surface & Coatings Technology. ,vol. 206, pp. 4411- 4416 ,(2012) , 10.1016/J.SURFCOAT.2012.04.076
A.S. Shahi, Sunil Pandey, Modelling of the effects of welding conditions on dilution of stainless steel claddings produced by gas metal arc welding procedures Journal of Materials Processing Technology. ,vol. 196, pp. 339- 344 ,(2008) , 10.1016/J.JMATPROTEC.2007.05.060
P. Gupta, G. Tenhundfeld, E.O. Daigle, D. Ryabkov, Electrolytic plasma technology: Science and engineering—An overview Surface & Coatings Technology. ,vol. 201, pp. 8746- 8760 ,(2007) , 10.1016/J.SURFCOAT.2006.11.023