Effect of pre-injection thermo-mechanical treatment on helium embrittlement of Fe-(25–40)Ni-15Cr austenitic alloys
作者： H. Shiraishi , N. Yamamoto , H. Shinno , H. Yoshida , H. Kamitsubo
DOI: 10.1016/0022-3115(83)90223-4
关键词: Metallurgy 、 Helium 、 Austenite 、 Alloy 、 Ductility 、 Elongation 、 Ultimate tensile strength 、 Materials science 、 Embrittlement 、 Precipitation hardening 、 Nuclear and High Energy Physics 、 General Materials Science 、 Nuclear Energy and Engineering
摘要: Abstract The effect of pre-injection treatments on helium embrittlement Fe-(25–40)Ni-Cr austenitic alloys with and without the addition Ti Nb was widely investigated using injection method a cyclotron. For precipitation hardened produced γ′-Ni 3 (Ti,Al) γ″-Ni Nb, total elongation injected materials rapidly decreased increase tensile strength. By comparing same alloy under various at strength level, treatments, such as cold work aging, were concluded to have beneficial ductility. non-hardenable alloys, degree is about order in 316 stainless steel Fe-25Ni-15Cr but increasing Ni content 35% caused more severe reduction for solution treated condition. ductility improving content.
elsevier.com
sci-hub.se 参考文章(18)
T. Furuta, S. Kawasaki, Influence of recrystallization on the high-temperature embrittlement of austenitic stainless steel induced by a- irradiation Journal of Nuclear Materials. ,vol. 47, pp. 102- 104 ,(1973) , 10.1016/0022-3115(73)90193-1
M.L. Grossbeck, P.J. Maziasz, Tensile properties of 20% cold-worked titanium-modified type 316 stainless steel irradiated in HFIR Journal of Nuclear Materials. ,vol. 104, pp. 827- 831 ,(1981) , 10.1016/0022-3115(82)90702-4
J.F. Bates, R.W. Powell, Irradiation-induced swelling in commercial alloys Journal of Nuclear Materials. ,vol. 102, pp. 200- 213 ,(1981) , 10.1016/0022-3115(81)90560-2
D. Kramer, H.R. Brager, C.G. Rhodes, A.G. Pard, Helium embrittlement in type 304 stainless steel Journal of Nuclear Materials. ,vol. 25, pp. 121- 131 ,(1968) , 10.1016/0022-3115(68)90038-X
T. Thorvaldsson, G. L. Dunlop, Precipitation reactions in Ti-stabilized austenitic stainless steel Metal science. ,vol. 14, pp. 513- 518 ,(1980) , 10.1179/030634580790426003
T. Furuta, S. Kawasaki, The influence of helium distribution and grain size on high-temperature embrittlement of stainless steel Journal of Nuclear Materials. ,vol. 50, pp. 275- 280 ,(1974) , 10.1016/0022-3115(74)90097-X
W. Kesternich, J. Rothaut, Reduction of helium embrittlement in stainless steel by finely dispersed TiC precipitates Journal of Nuclear Materials. ,vol. 104, pp. 845- 852 ,(1981) , 10.1016/0022-3115(82)90705-X
T. J. Headley, M. M. Karnowsky, W. R. Sorenson, Effect of composition and high energy rate forging on the onset of precipitation in an iron-base superalloy Metallurgical and Materials Transactions A-physical Metallurgy and Materials Science. ,vol. 13, pp. 345- 353 ,(1982) , 10.1007/BF02643343
W. B. Jones, R. M. Allen, Mechanical behavior of Alloy 800 at 838 K Metallurgical and Materials Transactions A-physical Metallurgy and Materials Science. ,vol. 13, pp. 637- 648 ,(1982) , 10.1007/BF02644429
P.J. Maziasz, T.K. Roche, Preirradiation microstructural development designed to minimize properties degradation during irradiation in austenitic alloys Journal of Nuclear Materials. ,vol. 104, pp. 797- 801 ,(1981) , 10.1016/0022-3115(82)90697-3