Experimental investigation of specific cutting energy and surface quality based on negative effective rake angle in micro turning
作者： Xian Wu , Liang Li , Meng Zhao , Ning He
DOI: 10.1007/S00170-015-7548-6
关键词: Turn (geometry) 、 Energy (signal processing) 、 Materials science 、 Optics 、 Surface roughness 、 Rake angle 、 Point (geometry) 、 Chip 、 Edge (geometry) 、 Radius
摘要: Since the uncut chip thickness is comparable to cutting edge radius, in fact, micro a negative rake angle process. The minimum has great effect on This paper presents an experimental investigation of specific energy and surface quality based effective turning. A new model developed calculate cutting. found be more with decreasing ratio radius. calculated about 0.2–0.3 times radius critical angle. turn point nonlinear increase observed at roughness also achieved near
springer.com
sci-hub.se 参考文章(24)
T.H.C. Childs, Surface energy, cutting edge radius and material flow stress size effects in continuous chip formation of metals Cirp Journal of Manufacturing Science and Technology. ,vol. 3, pp. 27- 39 ,(2010) , 10.1016/J.CIRPJ.2010.07.008
Kai Liu, Shreyes N. Melkote, Effect of plastic side flow on surface roughness in micro-turning process International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 1778- 1785 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.11.014
R. Komanduri, N. Chandrasekaran, L. M. Raff, Some aspects of machining with negative-rake tools simulating grinding: A molecular dynamics simulation approach Philosophical Magazine Part B. ,vol. 79, pp. 955- 968 ,(1999) , 10.1080/13642819908214852
M. Weber, T. Hochrainer, P. Gumbsch, H. Autenrieth, L. Delonnoy, V. Schulze, D. Löhe, J. Kotschenreuther, J. Fleischer, INVESTIGATION OF SIZE-EFFECTS IN MACHINING WITH GEOMETRICALLY DEFINED CUTTING EDGES Machining Science and Technology. ,vol. 11, pp. 447- 473 ,(2007) , 10.1080/10910340701697086
Milton Clayton Shaw, Metal cutting principles ,(1960)
F. Vollertsen, D. Biermann, H.N. Hansen, I.S. Jawahir, K. Kuzman, Size effects in manufacturing of metallic components CIRP Annals. ,vol. 58, pp. 566- 587 ,(2009) , 10.1016/J.CIRP.2009.09.002
X. Liu, R. E. DeVor, S. G. Kapoor, An Analytical Model for the Prediction of Minimum Chip Thickness in Micromachining Journal of Manufacturing Science and Engineering-transactions of The Asme. ,vol. 128, pp. 474- 481 ,(2006) , 10.1115/1.2162905
X. Wang, C.X. Feng, Development of Empirical Models for Surface Roughness Prediction in Finish Turning The International Journal of Advanced Manufacturing Technology. ,vol. 20, pp. 348- 356 ,(2002) , 10.1007/S001700200162
M. Lai, X. D. Zhang, F. Z. Fang, Study on critical rake angle in nanometric cutting Applied Physics A. ,vol. 108, pp. 809- 818 ,(2012) , 10.1007/S00339-012-6973-8
T.H.C. Childs, K. Sekiya, R. Tezuka, Y. Yamane, D. Dornfeld, D.-E. Lee, S. Min, P.K. Wright, Surface finishes from turning and facing with round nosed tools CIRP Annals. ,vol. 57, pp. 89- 92 ,(2008) , 10.1016/J.CIRP.2008.03.121