On the processing, microstructure, mechanical and wear properties of cermet/stainless steel layer composites
作者： Akhtar Farid , Shiju Guo
DOI: 10.1016/J.ACTAMAT.2006.10.009
关键词: Composite material 、 High-speed steel 、 Layer (electronics) 、 Microstructure 、 Tribology 、 Carbide 、 Materials science 、 Flexural strength 、 Toughness 、 Cermet
摘要: This study deals with layer composites of carbide reinforcements and stainless steel prepared successfully by powder technology. The layer material consisted of two layers. The …
elsevier.com
sci-hub.se 参考文章(27)
K. Das, T. K. Bandyopadhyay, S. Das, A Review on the various synthesis routes of TiC reinforced ferrous based composites Journal of Materials Science. ,vol. 37, pp. 3881- 3892 ,(2002) , 10.1023/A:1019699205003
J.C. Rawers, D.E. Alman, Fracture characteristics of metal/intermetallic laminar composites produced by reaction sintering and hot pressing Composites Science and Technology. ,vol. 54, pp. 379- 384 ,(1995) , 10.1016/0266-3538(95)00072-0
E. Pagounis, V. K. Lindroos, M. Talvitie, Influence of Matrix Structure on the Abrasion Wear Resistance and Toughness of a Hot Isostatic Pressed White Iron Matrix Composite Metallurgical and Materials Transactions A-physical Metallurgy and Materials Science. ,vol. 27, pp. 4183- 4191 ,(1996) , 10.1007/BF02595666
Irina Hussainova, Microstructure and erosive wear in ceramic-based composites Wear. ,vol. 258, pp. 357- 365 ,(2005) , 10.1016/J.WEAR.2004.01.024
B Yang, F Wang, J.S Zhang, Microstructural characterization of in situ TiC/Al and TiC/Al-20Si-5Fe-3Cu-1Mg composites prepared by spray deposition Acta Materialia. ,vol. 51, pp. 4977- 4989 ,(2003) , 10.1016/S1359-6454(03)00292-1
L. Lu, M.O. Lai, F.L. Chen, Al-4 wt% Cu Composite reinforced with in-situ TiB2 particles Acta Materialia. ,vol. 45, pp. 4297- 4309 ,(1997) , 10.1016/S1359-6454(97)00075-X
Farid Akhtar, SJ Guo, KA Shah, None, Effect of Cu3P addition on sintering behaviour of elemental powders in the composition of 465 stainless steel Powder Metallurgy. ,vol. 49, pp. 28- 33 ,(2006) , 10.1179/174329006X89344
Akhtar Farid, Shiju Guo, Feng-e Cui, Peizhong Feng, Tao Lin, TiB2 and TiC stainless steel matrix composites Materials Letters. ,vol. 61, pp. 189- 191 ,(2007) , 10.1016/J.MATLET.2006.04.028
R.C.D. Richardson, The wear of metals by relatively soft abrasives Wear. ,vol. 11, pp. 245- 275 ,(1968) , 10.1016/0043-1648(68)90175-0
Jüri Pirso, Mart Viljus, Sergei Letunovitš, Friction and dry sliding wear behaviour of cermets Wear. ,vol. 260, pp. 815- 824 ,(2006) , 10.1016/J.WEAR.2005.04.006