Microstructure and mechanical property of Cu2O–Cu cermet prepared by in-situ reduction-hot pressing method
作者： L.C. Feng , W.Z. Shao , L. Zhen , N. Xie
DOI: 10.1016/J.MATLET.2008.02.002
关键词: Metallurgy 、 Microstructure 、 Compressive strength 、 Pressing 、 Scanning electron microscope 、 Cermet 、 Optical microscope 、 Materials science 、 Hot pressing 、 Phase (matter)
摘要: Abstract Cu 2 O–Cu cermets were prepared by a novel method, hot pressing mixed C and O powders, in which the conductor was produced reaction between (called as in-situ reduction-hot method presented IRHP). Phase microstructures of characterized X-ray diffraction, optical microscope, scanning electron microscope. XRD analysis showed that only consist phases. Microstructural characterization distribution phase is homogeneous throughout matrix. The mechanical properties measured under universal tester, compressive strength with same content 1.5 times higher than samples powders directly HP).
elsevier.com
sci-hub.se 参考文章(8)
E. Olsen, J. Thonstad, Nickel ferrite as inert anodes in aluminium electrolysis: Part I Material fabrication and preliminary testing Journal of Applied Electrochemistry. ,vol. 29, pp. 293- 299 ,(1999) , 10.1023/A:1003460220418
E. Olsen, J. Thonstad, Nickel ferrite as inert anodes in aluminium electrolysis: Part II Material performance and long-term testing Journal of Applied Electrochemistry. ,vol. 29, pp. 301- 311 ,(1999) , 10.1023/A:1003464304488
L.John Berchmans, R.Kalai Selvan, C.O. Augustin, Evaluation of Mg2+-substituted NiFe2O4 as a green anode material Materials Letters. ,vol. 58, pp. 1928- 1933 ,(2004) , 10.1016/J.MATLET.2003.12.008
Y. Ji, J.A. Yeomans, Processing and mechanical properties of Al2O3–5 vol.% Cr nanocomposites Journal of The European Ceramic Society. ,vol. 22, pp. 1927- 1936 ,(2002) , 10.1016/S0955-2219(01)00528-3
W. Z. Shao, V. V. Ivanov, L. Zhen, Y. S. Cui, D. Z. Yang, Effect of porosity and copper content on compressive strength of Cu/Cu2O cermet Journal of Materials Science. ,vol. 39, pp. 731- 732 ,(2004) , 10.1023/B:JMSC.0000011543.88537.4B
Donald R. Sadoway, Inert anodes for the Hall-Héroult cell: The ultimate materials challenge JOM. ,vol. 53, pp. 34- 35 ,(2001) , 10.1007/S11837-001-0206-5
L.S. Sigl, P.A. Mataga, B.J. Dalgleish, R.M. McMeeking, A.G. Evans, On the toughness of brittle materials reinforced with a ductile phase Acta Metallurgica. ,vol. 36, pp. 945- 953 ,(1988) , 10.1016/0001-6160(88)90149-6
L. C. Feng, W. Z. Shao, L. Zhen, N. Xie, V. V. Ivanov, Cu2O/Cu Cermet as a Candidate Inert Anode for Al Production International Journal of Applied Ceramic Technology. ,vol. 4, pp. 453- 462 ,(2007) , 10.1111/J.1744-7402.2007.02154.X