Effect of heat treatment on microstructure and mechanical behaviours of 18Ni-300 maraging steel manufactured by selective laser melting
作者： Jun Song , Qian Tang , Qixiang Feng , Shuai Ma , Rossitza Setchi
DOI: 10.1016/J.OPTLASTEC.2019.105725
关键词: Ultimate tensile strength 、 Martensite 、 Materials science 、 Residual stress 、 Laser power scaling 、 Selective laser melting 、 Maraging steel 、 Indentation hardness 、 Composite material 、 Microstructure
摘要: … Selective laser melting (SLM) of 18Ni-300 maraging steel is … behaviour of SLM-built 18Ni-300 maraging steel. The experimental … from 18Ni-300 maraging steel using the SLM process. …
harvard.edu
sci-hub.se 参考文章(28)
K. Kempen, E. Yasa, L. Thijs, J.-P. Kruth, J. Van Humbeeck, Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel Physics Procedia. ,vol. 12, pp. 255- 263 ,(2011) , 10.1016/J.PHPRO.2011.03.033
Lore Thijs, Frederik Verhaeghe, Tom Craeghs, Jan Van Humbeeck, Jean-Pierre Kruth, A study of the microstructural evolution during selective laser melting of Ti–6Al–4V Acta Materialia. ,vol. 58, pp. 3303- 3312 ,(2010) , 10.1016/J.ACTAMAT.2010.02.004
G. Casalino, S.L. Campanelli, N. Contuzzi, A.D. Ludovico, Experimental investigation and statistical optimisation of the selective laser melting process of a maraging steel Optics and Laser Technology. ,vol. 65, pp. 151- 158 ,(2015) , 10.1016/J.OPTLASTEC.2014.07.021
Dongdong Gu, Yves-Christian Hagedorn, Wilhelm Meiners, Guangbin Meng, Rui João Santos Batista, Konrad Wissenbach, Reinhart Poprawe, Densification behavior, microstructure evolution, and wear performance of selective laser melting processed commercially pure titanium Acta Materialia. ,vol. 60, pp. 3849- 3860 ,(2012) , 10.1016/J.ACTAMAT.2012.04.006
Eric A. Jägle, Pyuck-Pa Choi, Jan Van Humbeeck, Dierk Raabe, Precipitation and austenite reversion behavior of a maraging steel produced by selective laser melting Journal of Materials Research. ,vol. 29, pp. 2072- 2079 ,(2014) , 10.1557/JMR.2014.204
Dacian Tomus, Yang Tian, Paul A. Rometsch, Martin Heilmaier, Xinhua Wu, Influence of post heat treatments on anisotropy of mechanical behaviour and microstructure of Hastelloy-X parts produced by selective laser melting Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 667, pp. 42- 53 ,(2016) , 10.1016/J.MSEA.2016.04.086
Riccardo Casati, Jannis Lemke, Ausonio Tuissi, Maurizio Vedani, Aging Behaviour and Mechanical Performance of 18-Ni 300 Steel Processed by Selective Laser Melting Metals. ,vol. 6, pp. 218- ,(2016) , 10.3390/MET6090218
W. Tillmann, C. Schaak, J. Nellesen, M. Schaper, M.E. Aydinöz, K.-P. Hoyer, Hot isostatic pressing of IN718 components manufactured by selective laser melting Additive manufacturing. ,vol. 13, pp. 93- 102 ,(2017) , 10.1016/J.ADDMA.2016.11.006
Bandar AlMangour, Dariusz Grzesiak, Jenn-Ming Yang, Selective laser melting of TiB2/316L stainless steel composites: The roles of powder preparation and hot isostatic pressing post-treatment Powder Technology. ,vol. 309, pp. 37- 48 ,(2017) , 10.1016/J.POWTEC.2016.12.073
Quanquan Han, Rossitza Setchi, Franck Lacan, Dongdong Gu, Sam L. Evans, Selective laser melting of advanced Al-Al 2 O 3 nanocomposites: simulation, microstructure and mechanical properties Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 698, pp. 162- 173 ,(2017) , 10.1016/J.MSEA.2017.05.061