Effect of Different Sintering Temperatures on Microstructure and Mechanical Properties for Pure Al Material Produced by Powder Metallurgy
作者： Uğur Avci , Abdulkadir Güleç
关键词:
摘要: Addressing the need for light materials in today’s industry, present study aims to analyze effects of sintering parameters on pure Al material manufactured using powder metallurgy technique. 99% and commercially obtained at a dimension 180 µm was subjected pre-heating placed specially designed die. compacted into die an upper punch with 500 MPa pressure later removed from conical process. In order find optimal temperature duration, samples were sintered separately 500oC, 550oC 600oC 45, 60 75 minutes each value. Microstructural analysis, microhardness test density sample process performed determine most durations given temperature, changes caused during these processes observed. Finally, different three temperatures tensile test. The findings all tests analyzed calculate Al.
sci-hub.st 参考文章(17)
Avijit Sinha, Zoheir Farhat, Effect of Surface Porosity on Tribological Properties of Sintered Pure Al and Al 6061 Materials Sciences and Applications. ,vol. 06, pp. 549- 566 ,(2015) , 10.4236/MSA.2015.66059
J.D.B. de Mello, R. Binder, A.N. Klein, I.M. Hutchings, Effect of compaction pressure and powder grade on microstructure and hardness of steam oxidised sintered iron Powder Metallurgy. ,vol. 44, pp. 53- 61 ,(2001) , 10.1179/003258901666176
Y.Y Li, T.L Ngai, D.T Zhang, Y Long, W Xia, Effect of die wall lubrication on warm compaction powder metallurgy Journal of Materials Processing Technology. ,vol. 129, pp. 354- 358 ,(2002) , 10.1016/S0924-0136(02)00648-9
F Bardi, M Cabibbo, E Evangelista, S Spigarelli, M Vukčevič, An analysis of hot deformation of an Al–Cu–Mg alloy produced by powder metallurgy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 339, pp. 43- 52 ,(2003) , 10.1016/S0921-5093(02)00103-X
Mehdi Rahimian, Nader Parvin, Naser Ehsani, INVESTIGATION OF PARTICLE SIZE AND AMOUNT OF ALUMINA ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF AL MATRIX COMPOSITE MADE BY POWDER METALLURGY Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 527, pp. 1031- 1038 ,(2010) , 10.1016/J.MSEA.2009.09.034
F Tang, I.E Anderson, S.B Biner, Solid state sintering and consolidation of Al powders and Al matrix composites Journal of Light Metals. ,vol. 2, pp. 201- 214 ,(2002) , 10.1016/S1471-5317(03)00004-X
A.D.P. LaDelpha, H. Neubing, D.P. Bishop, Metallurgical assessment of an emerging Al–Zn–Mg–Cu P/M alloy Materials Science and Engineering: A. ,vol. 520, pp. 105- 113 ,(2009) , 10.1016/J.MSEA.2009.05.039
Erfan Salahinejad, Rasool Amini, Mehdi Marasi, Mohammad Jafar Hadianfard, The effect of sintering time on the densification and mechanical properties of a mechanically alloyed Cr―Mn―N stainless steel Materials & Design. ,vol. 31, pp. 527- 532 ,(2010) , 10.1016/J.MATDES.2009.07.024
Mehdi Rahimian, Naser Ehsani, Nader Parvin, Hamid reza Baharvandi, The effect of particle size, sintering temperature and sintering time on the properties of Al–Al2O3 composites, made by powder metallurgy Journal of Materials Processing Technology. ,vol. 209, pp. 5387- 5393 ,(2009) , 10.1016/J.JMATPROTEC.2009.04.007
M. Sobhani, T. Ebadzadeh, M.R. Rahimipour, Formation and densification behavior of reaction sintered alumina–20 wt.% aluminium titanate nano-composites International Journal of Refractory Metals & Hard Materials. ,vol. 47, pp. 49- 53 ,(2014) , 10.1016/J.IJRMHM.2014.06.018