Effect of wire brushing on warm roll bonding of 6XXX/5XXX/6XXX aluminum alloy clad sheets
作者： Su-Hyeon Kim , Hyoung-Wook Kim , Kwangjun Euh , Joo-Hee Kang , Jae-Hyung Cho
DOI: 10.1016/J.MATDES.2011.09.024
关键词:
摘要: … A high-strength 7075 Al alloy has also been roll-bonded to … reduction and bonding strength of warm roll-bonded sheets … Entrance analysis of 7075 Al/Mg–Gd–Y–Zr/7075 Al laminated …
elsevier.com
sci-hub.se 参考文章(24)
X. K. Peng, G. Heness, W. Y. Yeung, Effect of rolling temperature on interface and bond strength development of roll bonded copper/aluminium metal laminates Journal of Materials Science. ,vol. 34, pp. 277- 281 ,(1999) , 10.1023/A:1004497304095
M. Movahedi, H.R. Madaah-Hosseini, A.H. Kokabi, The influence of roll bonding parameters on the bond strength of Al-3003/Zn soldering sheets Materials Science and Engineering: A. ,vol. 487, pp. 417- 423 ,(2008) , 10.1016/J.MSEA.2007.10.019
M. Eizadjou, H. Danesh Manesh, K. Janghorban, Investigation of roll bonding between aluminum alloy strips Materials & Design. ,vol. 29, pp. 909- 913 ,(2008) , 10.1016/J.MATDES.2007.03.020
L. Zhang, L. Meng, S.P. Zhou, F.T. Yang, Behaviors of the interface and matrix for the Ag/Cu bimetallic laminates prepared by roll bonding and diffusion annealing Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 371, pp. 65- 71 ,(2004) , 10.1016/S0921-5093(03)00626-9
F. Carreño, J. Chao, M. Pozuelo, O.A. Ruano, Microstructure and fracture properties of an ultrahigh carbon steel–mild steel laminated composite Scripta Materialia. ,vol. 48, pp. 1135- 1140 ,(2003) , 10.1016/S1359-6462(02)00602-4
X.P. Zhang, T.H. Yang, S. Castagne, J.T. Wang, Microstructure; bonding strength and thickness ratio of Al/Mg/Al alloy laminated composites prepared by hot rolling Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 528, pp. 1954- 1960 ,(2011) , 10.1016/J.MSEA.2010.10.105
C.M. Cepeda-Jiménez, M. Pozuelo, O.A. Ruano, F. Carreño, Influence of the thermomechanical processing on the fracture mechanisms of high strength aluminium/pure aluminium multilayer laminate materials Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 490, pp. 319- 327 ,(2008) , 10.1016/J.MSEA.2008.01.034
M. Eizadjou, H. Danesh Manesh, K. Janghorban, Mechanism of warm and cold roll bonding of aluminum alloy strips Materials & Design. ,vol. 30, pp. 4156- 4161 ,(2009) , 10.1016/J.MATDES.2009.04.036
Jiantao Liu, Ming Li, Simon Sheu, M.E. Karabin, R.W. Schultz, Macro-and micro-surface engineering to improve hot roll bonding of aluminum plate and sheet Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 479, pp. 45- 57 ,(2008) , 10.1016/J.MSEA.2007.06.022
M. Soltan Ali Nezhad, A. Haerian Ardakani, A study of joint quality of aluminum and low carbon steel strips by warm rolling Materials & Design. ,vol. 30, pp. 1103- 1109 ,(2009) , 10.1016/J.MATDES.2008.06.042