The potential for scaling ECAP: effect of sample size on grain refinement and mechanical properties
作者： Zenji Horita , Takayoshi Fujinami , Terence G Langdon
DOI: 10.1016/S0921-5093(01)01339-9
关键词:
摘要: … Earlier results suggested a possible lower limit for satisfactory ECAP because there was … in ECAP using rod-shaped samples with diameters from 6–40 mm. In addition the ECAP facility …
elsevier.com
sci-hub.se 参考文章(21)
Investigations and applications of severe plastic deformation Kluwer Academic Publishers. ,(2000) , 10.1007/978-94-011-4062-1
J. Wang, Y. Iwahashi, Z. Horita, M. Furukawa, M. Nemoto, R.Z. Valiev, T.G. Langdon, An investigation of microstructural stability in an Al-Mg alloy with submicrometer grain size Acta Materialia. ,vol. 44, pp. 2973- 2982 ,(1996) , 10.1016/1359-6454(95)00395-9
S.L. Semiatin, D.P. DeLo, E.B. Shell, The effect of material properties and tooling design on deformation and fracture during equal channel angular extrusion Acta Materialia. ,vol. 48, pp. 1841- 1851 ,(2000) , 10.1016/S1359-6454(00)00019-7
Hiroki Akamatsu, Takayoshi Fujinami, Zenji Horita, Terence G Langdon, Influence of rolling on the superplastic behavior of an Al-Mg-Sc alloy after ECAP Scripta Materialia. ,vol. 44, pp. 759- 764 ,(2001) , 10.1016/S1359-6462(00)00666-7
Terence G. Langdon, Minoru Furukawa, Minoru Nemoto, Zenji Horita, Using equal-channel angular pressing for refining grain size JOM. ,vol. 52, pp. 30- 33 ,(2000) , 10.1007/S11837-000-0128-7
Shogo Komura, Zenji Horita, Minoru Furukawa, Minoru Nemoto, Terence G. Langdon, Influence of scandium on superplastic ductilities in an Al–Mg–Sc alloy Journal of Materials Research. ,vol. 15, pp. 2571- 2576 ,(2000) , 10.1557/JMR.2000.0367
Z Horita, M Furukawa, M Nemoto, A.J Barnes, T.G Langdon, Superplastic forming at high strain rates after severe plastic deformation Acta Materialia. ,vol. 48, pp. 3633- 3640 ,(2000) , 10.1016/S1359-6454(00)00182-8
S.L. Semiatin, D.P. DeLo, Equal channel angular extrusion of difficult-to-work alloys Materials & Design. ,vol. 21, pp. 311- 322 ,(1998) , 10.1016/S0261-3069(99)00085-0
P.B. Prangnell, C. Harris, S.M. Roberts, Finite element modelling of equal channel angular extrusion Scripta Materialia. ,vol. 37, pp. 983- 989 ,(1997) , 10.1016/S1359-6462(97)00192-9
Y. Iwahashi, Z. Horita, M. Nemoto, T.G. Langdon, An investigation of microstructural evolution during equal-channel angular pressing Acta Materialia. ,vol. 45, pp. 4733- 4741 ,(1997) , 10.1016/S1359-6454(97)00100-6