Thermal and mechanical modeling analysis of laser-assisted micro-milling of difficult-to-machine alloys
作者： Hongtao Ding , Ninggang Shen , Yung C. Shin
DOI: 10.1016/J.JMATPROTEC.2011.07.016
关键词:
摘要: … -assisted micro-milling (LAMM) of difficult-to-machine alloys, such as Ti6Al4V, Inconel 718, … models developed for the size effect in micro-milling. The steady-state workpiece and tool …
elsevier.com
sci-hub.se 参考文章(37)
S. Melkote, M. Kumar, F. Hashimoto, G. Lahoti, Laser assisted micro-milling of hard-to-machine materials CIRP Annals. ,vol. 58, pp. 45- 48 ,(2009) , 10.1016/J.CIRP.2009.03.053
Ramesh Singh, Matthew J. Alberts, Shreyes N. Melkote, Characterization and prediction of the heat-affected zone in a laser-assisted mechanical micromachining process International Journal of Machine Tools and Manufacture. ,vol. 48, pp. 994- 1004 ,(2008) , 10.1016/J.IJMACHTOOLS.2008.01.004
N. Fang, P. Dewhurst, Slip-line modeling of built-up edge formation in machining International Journal of Mechanical Sciences. ,vol. 47, pp. 1079- 1098 ,(2005) , 10.1016/J.IJMECSCI.2005.02.008
S.M. Afazov, S.M. Ratchev, J. Segal, Modelling and simulation of micro-milling cutting forces Journal of Materials Processing Technology. ,vol. 210, pp. 2154- 2162 ,(2010) , 10.1016/J.JMATPROTEC.2010.07.033
Ramesh Singh, Shreyes N. Melkote, Characterization of a hybrid laser-assisted mechanical micromachining (LAMM) process for a difficult-to-machine material International Journal of Machine Tools & Manufacture. ,vol. 47, pp. 1139- 1150 ,(2007) , 10.1016/J.IJMACHTOOLS.2006.09.004
Atul Dhanorker, Tugˇrul O¨ zel, None, AN EXPERIMENTAL AND MODELING STUDY ON MESO/MICRO END MILLING PROCESS ASME 2006 International Manufacturing Science and Engineering Conference. pp. 1071- 1079 ,(2006) , 10.1115/MSEC2006-21127
K. Ohgo, The adhesion mechanism of the built-up edge and the layer on the rake face of a cutting tool Wear. ,vol. 51, pp. 117- 126 ,(1978) , 10.1016/0043-1648(78)90059-5
Jonathan A. Shelton, Yung C. Shin, Experimental Evaluation of Laser-Assisted Micromilling in a Slotting Configuration Journal of Manufacturing Science and Engineering-transactions of The Asme. ,vol. 132, pp. 021008- ,(2010) , 10.1115/1.4001142
Balkrishna Rao, Chinmaya R. Dandekar, Yung C. Shin, An experimental and numerical study on the face milling of Ti–6Al–4V alloy: Tool performance and surface integrity Journal of Materials Processing Technology. ,vol. 211, pp. 294- 304 ,(2011) , 10.1016/J.JMATPROTEC.2010.10.002
X. Liu, R. E. DeVor, S. G. Kapoor, An Analytical Model for the Prediction of Minimum Chip Thickness in Micromachining Journal of Manufacturing Science and Engineering-transactions of The Asme. ,vol. 128, pp. 474- 481 ,(2006) , 10.1115/1.2162905