Effects of environmental conditions, aging, and build orientations on the mechanical properties of ASTM type I specimens manufactured via stereolithography
作者： Karina Puebla , Karina Arcaute , Rolando Quintana , Ryan B. Wicker
DOI: 10.1108/13552541211250373
关键词:
摘要: Purpose – The purpose of this paper is to investigate the effects aging, pre‐conditioning, and build orientation on mechanical properties test samples fabricated using stereolithography (SL) a commercially available resin.Design/methodology/approach American Society for Testing Materials (ASTM) Standard D638 Type I specimens were manufactured in Viper si2 SL system WaterShed™ 11120 resin. two different setups, designed fit batches 18 or 24 with orientations. randomly tested tension, design experiments (DOE) was used determine effect aging (4, 30 120 days), pre‐conditioning (ambient, desiccant, ASTM recommended conditioning), (flat, an edge, vertical) ultimate tensile stress (UTS) elastic modulus (E) samples. Additionally, fractured imaged scanning electron microscopy (SEM) charac...
sci-hub.se 参考文章(26)
John Scheirs, Compositional and Failure Analysis of Polymers: A Practical Approach ,(2000)
J. Hector Sandoval, Ryan B. Wicker, Functionalizing stereolithography resins: effects of dispersed multi‐walled carbon nanotubes on physical properties Rapid Prototyping Journal. ,vol. 12, pp. 292- 303 ,(2006) , 10.1108/13552540610707059
Xavier Ottemer, Jonathan S. Colton, Effects of aging on epoxy‐based rapid tooling materials Rapid Prototyping Journal. ,vol. 8, pp. 215- 223 ,(2002) , 10.1108/13552540210441120
Prashant Kulkarni, Anne Marsan, Debasish Dutta, A review of process planning techniques in layered manufacturing Rapid Prototyping Journal. ,vol. 6, pp. 18- 35 ,(2000) , 10.1108/13552540010309859
J. H. Sandoval, K. F. Soto, L. E. Murr, R. B. Wicker, Nanotailoring photocrosslinkable epoxy resins with multi-walled carbon nanotubes for stereolithography layered manufacturing Journal of Materials Science. ,vol. 42, pp. 156- 165 ,(2007) , 10.1007/S10853-006-1035-2
Rolando Quintana, Jae-Won Choi, Karina Puebla, Ryan Wicker, Effects of build orientation on tensile strength for stereolithography-manufactured ASTM D-638 type I specimens. The International Journal of Advanced Manufacturing Technology. ,vol. 46, pp. 201- 215 ,(2010) , 10.1007/S00170-009-2066-Z
Xing Yang Liu, Jiaren Jiang, Environmental effects on the dimensions of SL5195 resin Rapid Prototyping Journal. ,vol. 9, pp. 88- 94 ,(2003) , 10.1108/13552540310698152
W. Cheng, J.Y.H. Fuh, A.Y.C. Nee, Y.S. Wong, H.T. Loh, T. Miyazawa, Multi‐objective optimization of part‐ building orientation in stereolithography Rapid Prototyping Journal. ,vol. 1, pp. 12- 23 ,(1995) , 10.1108/13552549510104429
Joel E. McClurkin, David W. Rosen, Computer‐aided build style decision support for stereolithography Rapid Prototyping Journal. ,vol. 4, pp. 4- 13 ,(1998) , 10.1108/13552549810197505
D. Karalekas, K. Antoniou, Composite rapid prototyping: overcoming the drawback of poor mechanical properties Journal of Materials Processing Technology. ,vol. 153, pp. 526- 530 ,(2004) , 10.1016/J.JMATPROTEC.2004.04.019