Characterization and Properties of Iron/Silica-Sand-Nanoparticle Composites
作者： Tahir Ahmad , Othman Mamat
DOI: 10.4028/WWW.SCIENTIFIC.NET/DDF.316-317.97
关键词:
摘要: Copper-based microcomposites fabricated by powder metallurgy with subsequent plastic deformation have received increasing attention over recent years. These possess good electrical conductivity in combination high mechanical properties. The present study aims to explore potential technical merits developing a prealloyed copper based composites silica sand nanoparticles reinforcement. Relevant properties and improvements are the main targets. A composite 5, 10, 15 20 wt.% of were developed through process. It was observed that addition 20% increased hardness up 143HV. Optimum achieved nanoparticles. Advanced particle rearrangement mechanism due homogeneous fine distribution into pore sites also observed. much more surface-related seen be improved convincingly compared bulk controlled.
sci-hub.se 参考文章(21)
Rungtip Krataithong, Nattaya Torsangtum, Monnapas Morakotjinda, Bhanu Vetayanugul, Thanyaporn Yodkaew, Sainatee Chakthin, Pisarn Siriphol, Klong Luang, Nandh Thavarungkul, Ornmanee Coovattanachai, Influence of Carbides on Properties of Sintered Fe-Base Composites ,(2008)
Genadii A. Baglyuk, Leonid A. Posnyak, Powder Metallurgy Wear-Resistant Materials Based on Iron. Part 1. Materials Prepared by Sintering and Infiltration Powder Metallurgy and Metal Ceramics. ,vol. 40, pp. 34- 39 ,(2001) , 10.1023/A:1011399504008
Randall M. German, Powder Metallurgy of Iron and Steel ,(1998)
Interzum, Peter Zec, Material and design Red dot edition. ,(2007)
William D. Callister, Materials Science and Engineering: An Introduction ,(1985)
Karabi Das, T.K. Bandyopadhyay, Synthesis and characterization of zirconium carbide-reinforced iron-based composite Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 379, pp. 83- 91 ,(2004) , 10.1016/J.MSEA.2003.12.022
S. Libardi, M. Leoni, L. Facchini, M. D’Incau, P. Scardi, A. Molinari, Effect of the dispersion of nanometric silica particles on the thermal stability of a nanostructured iron based powder Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 445, pp. 244- 250 ,(2007) , 10.1016/J.MSEA.2006.09.035
Katsuyoshi Kondoh, Hisashi Imai, Yoshiharu Kosaka, Akimichi Kojima, Junko Umeda, Machinable Cu-40%Zn Composites Containing Graphite Particles by Powder Metallurgy Process Journal of Metallurgy. ,vol. 2009, pp. 1- 4 ,(2009) , 10.1155/2009/853092
Y. B. Liu, S. C. Lim, L. Lu, M. O. Lai, Recent development in the fabrication of metal matrix-particulate composites using powder metallurgy techniques Journal of Materials Science. ,vol. 29, pp. 1999- 2007 ,(1994) , 10.1007/BF01154673
R. Subramanian, C.G. McKamey, J.H. Schneibel, L.R. Buck, P.A. Menchhofer, Iron aluminide–Al2O3 composites by in situ displacement reactions: processing and mechanical properties Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 254, pp. 119- 128 ,(1998) , 10.1016/S0921-5093(98)00702-3