Tribological performance of uncoated and TiCN-coated D2, M2 and M4 steels under lubricated condition
作者： Luis Daniel Aguilera Camacho , Santos García Miranda , Karla Judith Moreno
DOI: 10.1016/S1006-706X(17)30122-X
关键词:
摘要: Abstract Hard coatings are used to improve the wear resistance of metals which largely depends on adhesion between substrate and coating. The friction behavior uncoated TiCN-coated D2, M2 M4 steels were evaluated by a pin-on-disk test under lubricated conditions. In order evaluate influence lubricant performance, dry tests also performed. results showed that coefficients very similar for both steels. Under conditions, D2 tool steel exhibited lowest coefficient, but presented smallest rate. Abrasion was main mechanism in all tribocouples. Additionally, microhardness measurements carried out, finding an hardness coatings. Besides, conducted, suggesting good class 1 substrates TiCN
springer.com
sci-hub.se 参考文章(16)
J. Lesage, D. Chicot, A. Pertuz, P.-Y. Jouan, N. Horny, A. Soom, A model for hardness determination of thin coatings from standard micro-indentation tests Surface & Coatings Technology. ,vol. 200, pp. 886- 889 ,(2005) , 10.1016/J.SURFCOAT.2005.01.056
Min-xian Wei, Shu-qi Wang, Lan Wang, Xiang-hong Cui, Kang-min Chen, Selection of Heat Treatment Process and Wear Mechanism of High Wear Resistant Cast Hot-Forging Die Steel Journal of Iron and Steel Research International. ,vol. 19, pp. 50- 57 ,(2012) , 10.1016/S1006-706X(12)60099-5
F. Velasco, E. Gordo, R. Isabel, E.M. Ruiz-Navas, A. Bautista, J.M. Torralba, Mechanical and wear behaviour of high-speed steels reinforced with TiCN particles International Journal of Refractory Metals and Hard Materials. ,vol. 19, pp. 319- 323 ,(2001) , 10.1016/S0263-4368(01)00053-1
Rahul Premachandran Nair, Drew Griffin, Nicholas X. Randall, The use of the pin-on-disk tribology test method to study three unique industrial applications Wear. ,vol. 267, pp. 823- 827 ,(2009) , 10.1016/J.WEAR.2009.02.026
Jianghong Gong, Hezhuo Miao, Zhe Zhao, Zhenduo Guan, Load-dependence of the measured hardness of Ti(C,N)-based cermets Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 303, pp. 179- 186 ,(2001) , 10.1016/S0921-5093(00)01845-1
Y. L. Su, W. H. Kao, Tribological behavior and wear mechanisms of TiN/TiCN/TiN multilayer coatings Journal of Materials Engineering and Performance. ,vol. 7, pp. 601- 612 ,(1998) , 10.1361/105994998770347440
Fjodor Sergejev, Priidu Peetsalu, Alina Sivitski, Mart Saarna, Eron Adoberg, Surface fatigue and wear of PVD coated punches during fine blanking operation Engineering Failure Analysis. ,vol. 18, pp. 1689- 1697 ,(2011) , 10.1016/J.ENGFAILANAL.2011.02.011
V. Leskovšek, B. Ule, Improved vacuum heat-treatment for fine-blanking tools from high-speed steel M2 Journal of Materials Processing Technology. ,vol. 82, pp. 89- 94 ,(1998) , 10.1016/S0924-0136(98)00023-5
N. Vidakis, A. Antoniadis, N. Bilalis, The vdi 3198 indentation test evaluation of a reliable qualitative control for layered compounds Journal of Materials Processing Technology. ,vol. 143, pp. 481- 485 ,(2003) , 10.1016/S0924-0136(03)00300-5
S. Thipprakmas, Improving wear resistance of sprocket parts using a fine-blanking process Wear. ,vol. 271, pp. 2396- 2401 ,(2011) , 10.1016/J.WEAR.2010.12.015