Necessity of multidimensional evaluation of the high-speed ball-end milled surface of hardened AISI D2 steel from a wear resistance perspective
作者： Weimin Huang , Jun Zhao , Suyu Wang
DOI: 10.1007/S00170-019-03768-1
关键词:
摘要: This paper focuses on revealing the anisotropy of surface integrity and wear resistance of high-speed ball-end milled surfaces of hardened cold work die steel AISI D2. Dry milling tests were performed on a five-axis high-speed machining center by using a two-edged coated solid carbide ball-end milling cutter. Then, wear resistance of a hard milled surface was evaluated through block-on-ring wear tests under unlubricated condition. Results showed that ball-end milled surfaces present anisotropic characteristics in terms of surface …
springer.com
sci-hub.se 参考文章(22)
W. H. Broughton, A. R. Kutzak, J. R. Cahoon, The determination of yield strength from hardness measurements Metallurgical Transactions. ,vol. 2, pp. 1979- 1983 ,(1971) , 10.1007/BF02913433
Noushin Yasavol, Amilcar Ramalho, Wear properties of friction stir processed AISI D2 tool steel Tribology International. ,vol. 91, pp. 177- 183 ,(2015) , 10.1016/J.TRIBOINT.2015.07.001
Sarwar Ali Abbasi, Pingfa Feng, Y Ma, XC Cai, DW Yu, ZJ Wu, Influence of tool inclination angle and cutting direction on long thin-walled part’s dimensional and geometric accuracy when high-speed ball end milling the heat-treated titanium alloy Ti–6Al–4 V Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. ,vol. 230, pp. 2676- 2698 ,(2016) , 10.1177/0954406215601451
Y. B. Guo, R. A. Waikar, An Experimental Study on the Effect of Machining-Induced White Layer on Frictional and Wear Performance at Dry and Lubricated Sliding Contact Tribology Transactions. ,vol. 53, pp. 127- 136 ,(2009) , 10.1080/10402000903283250
R. Lakshmipathy, R. Sagar, Effect of die surface topography on die-work interfacial friction in open die forging International Journal of Machine Tools & Manufacture. ,vol. 32, pp. 685- 693 ,(1992) , 10.1016/0890-6955(92)90023-A
R.S. Pawade, Suhas S. Joshi, P.K. Brahmankar, Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718 International Journal of Machine Tools and Manufacture. ,vol. 48, pp. 15- 28 ,(2008) , 10.1016/J.IJMACHTOOLS.2007.08.004
Mario Lopes Magri, Anselmo Eduardo Diniz, Sérgio Tonini Button, Influence of surface topography on the wear of hot forging dies The International Journal of Advanced Manufacturing Technology. ,vol. 65, pp. 459- 471 ,(2013) , 10.1007/S00170-012-4185-1
Kritika Singh, Rajesh K. Khatirkar, Sanjay G. Sapate, Microstructure evolution and abrasive wear behavior of D2 steel Wear. pp. 206- 216 ,(2015) , 10.1016/J.WEAR.2015.02.019
Linhu Tang, Chengxiu Gao, Jianlong Huang, Hongyan Zhang, Wenchun Chang, Dry sliding friction and wear behaviour of hardened AISI D2 tool steel with different hardness levels Tribology International. ,vol. 66, pp. 165- 173 ,(2013) , 10.1016/J.TRIBOINT.2013.05.006
Pradeep L. Menezes, K. Kumar, Kishore, Satish V. Kailas, Influence of friction during forming processes—a study using a numerical simulation technique The International Journal of Advanced Manufacturing Technology. ,vol. 40, pp. 1067- 1076 ,(2009) , 10.1007/S00170-008-1425-5