Simulation of Erosion by Particle Impact on a Rough Surface
作者： Ali Pourkamali Anaraki , Javad Kadkhodapour , Bahman Taherkhani
DOI: 10.1007/S11668-014-9886-3
关键词:
摘要: In many industrial conditions, we deal with impact of particles on a surface that can cause premature failure. A series studies have been conducted to investigate the effect parameters this phenomenon smooth surfaces at micron-scale. But there is no ideally micron level. Our study investigated particle erosion rate rough and obtained their diagram in terms rate. The modeled velocity was range between 25 150 m/s, diameter 216 1080 μm. our numerical study, an model based single small area described. Then, experimental different zones are created due multiple large were identified.
springer.com
sci-hub.se 参考文章(18)
S. Hassani, M. Bielawski, W. Beres, L. Martinu, M. Balazinski, J.E. Klemberg-Sapieha, Predictive tools for the design of erosion resistant coatings Surface & Coatings Technology. ,vol. 203, pp. 204- 210 ,(2008) , 10.1016/J.SURFCOAT.2008.08.050
Prabu Balu, Fanrong Kong, Syed Hamid, Radovan Kovacevic, Finite element modeling of solid particle erosion in AISI 4140 steel and nickel–tungsten carbide composite material produced by the laser-based powder deposition process Tribology International. ,vol. 62, pp. 18- 28 ,(2013) , 10.1016/J.TRIBOINT.2013.01.021
Na Zhang, Fan Yang, Lei Li, Changyu Shen, Jose Castro, L. James Lee, Thickness effect on particle erosion resistance of thermoplastic polyurethane coating on steel substrate Wear. ,vol. 303, pp. 49- 55 ,(2013) , 10.1016/J.WEAR.2013.02.022
K. Shimizu, T. Noguchi, H. Seitoh, M. Okada, Y. Matsubara, FEM analysis of erosive wear Wear. ,vol. 250, pp. 779- 784 ,(2001) , 10.1016/S0043-1648(01)00716-5
Mariusz Bielawski, Wieslaw Beres, FE modelling of surface stresses in erosion-resistant coatings under single particle impact Wear. ,vol. 262, pp. 167- 175 ,(2007) , 10.1016/J.WEAR.2006.04.009
M.S. ElTobgy, E. Ng, M.A. Elbestawi, Finite element modeling of erosive wear International Journal of Machine Tools & Manufacture. ,vol. 45, pp. 1337- 1346 ,(2005) , 10.1016/J.IJMACHTOOLS.2005.01.007
B. Staniša, V. Ivušić, Erosion behaviour and mechanisms for steam turbine rotor blades Wear. pp. 395- 400 ,(1995) , 10.1016/0043-1648(95)07136-9
Biraj Singh Thapa, Bhola Thapa, Ole G. Dahlhaug, Empirical modelling of sediment erosion in Francis turbines Energy. ,vol. 41, pp. 386- 391 ,(2012) , 10.1016/J.ENERGY.2012.02.066
Narayanan Ramanujam, Toshio Nakamura, Erosion mechanisms of thermally sprayed coatings with multiple phases Surface & Coatings Technology. ,vol. 204, pp. 42- 53 ,(2009) , 10.1016/J.SURFCOAT.2009.06.024
Baran Yıldırım, Sinan Müftü, Simulation and analysis of the impact of micron-scale particles onto a rough surface International Journal of Solids and Structures. ,vol. 49, pp. 1375- 1386 ,(2012) , 10.1016/J.IJSOLSTR.2012.02.018