Influence of nano ZrC content on tribological analysis, microstructure and mechanical properties of Cu–4Cr matrix composites produced by hot extrusion
作者： Natarajan Selvakumar , Sreedharan Christopher Ezhil Singh
DOI: 10.1016/J.ACME.2016.03.007
关键词:
摘要: Abstract In the present study, Cu–4Cr–xZrC nanocomposites have been developed through powder metallurgy route by varying proportions of zirconium carbide viz. (0–10 wt.%). The required green compacts were prepared using die set assembly in a compression testing machine. Consequently, hot extruded samples tested for dry sliding wear and friction pin-on-disc SEM, XRD, pin on-disc system Vickers hardness tester used to evaluate characterization, tribological properties respectively nanocomposites. From observations, it was found that coefficient increased progressively with increasing load distance. Furthermore, specific rate (SWR) decreased when compared composites pure copper. Hardness increases addition nano ZrC content into matrix composites.
harvard.edu
sci-hub.se 参考文章(19)
Amera G. Baker, Study of Mechanical and Physical Properties for SiC/ Al Composites International Journal of Advances in Applied Sciences. ,vol. 2, pp. 67- 72 ,(2013) , 10.11591/IJAAS.V2.I2.PP67-72
Suhrit Mula, Pankajini Sahani, S.K. Pratihar, Siddhartha Mal, Carl C. Koch, Mechanical properties and electrical conductivity of Cu–Cr and Cu–Cr–4% SiC nanocomposites for thermo-electric applications Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 528, pp. 4348- 4356 ,(2011) , 10.1016/J.MSEA.2011.03.040
L. Zhang, X.B. He, X.H. Qu, B.H. Duan, X. Lu, M.L. Qin, Dry sliding wear properties of high volume fraction SiCp/Cu composites produced by pressureless infiltration Wear. ,vol. 265, pp. 1848- 1856 ,(2008) , 10.1016/J.WEAR.2008.04.029
S.C. Vettivel, N. Selvakumar, N. Leema, A. Haiter Lenin, Electrical resistivity, wear map and modeling of extruded tungsten reinforced copper composite Materials & Design. ,vol. 56, pp. 791- 806 ,(2014) , 10.1016/J.MATDES.2013.11.070
R.K. Gautam, S. Ray, Satish C. Sharma, S.C. Jain, R. Tyagi, Dry sliding wear behavior of hot forged and annealed Cu–Cr–graphite in-situ composites Wear. ,vol. 271, pp. 658- 664 ,(2011) , 10.1016/J.WEAR.2010.11.033
S. Sheibani, S. Heshmati-Manesh, A. Ataie, Influence of Al2O3 nanoparticles on solubility extension of Cr in Cu by mechanical alloying Acta Materialia. ,vol. 58, pp. 6828- 6834 ,(2010) , 10.1016/J.ACTAMAT.2010.09.012
N. Selvakumar, S.C. Vettivel, Thermal, electrical and wear behavior of sintered Cu–W nanocomposite Materials & Design. ,vol. 46, pp. 16- 25 ,(2013) , 10.1016/J.MATDES.2012.09.055
W.X Qi, J.P Tu, F Liu, Y.Z Yang, N.Y Wang, H.M Lu, X.B Zhang, S.Y Guo, M.S Liu, Microstructure and tribological behavior of a peak aged Cu–Cr–Zr alloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 343, pp. 89- 96 ,(2003) , 10.1016/S0921-5093(02)00387-8
Hülya Kaftelen, M. Lütfi Öveçoğlu, Hani Henein, Hüseyin Çimenoğlu, ZrC particle reinforced Al–4 wt.% Cu alloy composites fabricated by mechanical alloying and vacuum hot pressing: Microstructural evaluation and mechanical properties Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 527, pp. 5930- 5938 ,(2010) , 10.1016/J.MSEA.2010.06.007
S.C. Vettivel, N. Selvakumar, R. Narayanasamy, N. Leema, Numerical modelling, prediction of Cu–W nano powder composite in dry sliding wear condition using response surface methodology Materials & Design. ,vol. 50, pp. 977- 996 ,(2013) , 10.1016/J.MATDES.2013.03.072