Effect of solution heat treatment on gas porosity and mechanical properties in a die cast step test part manufactured with a new AlSi10MnMg(Fe) secondary alloy
作者： A. Niklas , S. Orden , A. Bakedano , M. da Silva , E. Nogués
DOI: 10.1016/J.MSEA.2016.05.024
关键词:
摘要: Abstract The effect of heat treatment on gas porosity and mechanical properties was investigated in a step test part manufactured by vacuum assisted high pressure die casting using new AlSi10MnMg(Fe) secondary alloy. Porosity were the T6 temper with different solution treatments. characterized metallographic fractographic analysis tensile specimens. Mechanical comparable to corresponding primary alloy have been achieved for each treatment. It found that increasing temperature time increased yield ultimate strength, while elongation decreased observed sections fracture surfaces increased. evaluation indicates local area fraction rather than one whole surface determines ductility. size largest pore appears become more relevant above values 200 µm.
sci-hub.se 参考文章(14)
Edward J. Vinarcik, High Integrity Die Casting Processes ,(2002)
Gianni Nicoletto, Giancarlo Anzelotti, Radomila Konečná, X-ray computed tomography vs. metallography for pore sizing and fatigue of cast Al-alloys Procedia Engineering. ,vol. 2, pp. 547- 554 ,(2010) , 10.1016/J.PROENG.2010.03.059
X.P. Niu, B.H. Hu, I. Pinwill, H. Li, Vacuum assisted high pressure die casting of aluminium alloys Journal of Materials Processing Technology. ,vol. 105, pp. 119- 127 ,(2000) , 10.1016/S0924-0136(00)00545-8
S.G. Shabestari, The effect of iron and manganese on the formation of intermetallic compounds in aluminum–silicon alloys Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 383, pp. 289- 298 ,(2004) , 10.1016/J.MSEA.2004.06.022
Sumanth Shankar, Diran Apelian, Die soldering: Mechanism of the interface reaction between molten aluminum alloy and tool steel Metallurgical and Materials Transactions B-process Metallurgy and Materials Processing Science. ,vol. 33, pp. 465- 476 ,(2002) , 10.1007/S11663-002-0057-7
J.P. Weiler, J.T. Wood, R.J. Klassen, E. Maire, R. Berkmortel, G. Wang, Relationship between internal porosity and fracture strength of die-cast magnesium AM60B alloy Materials Science and Engineering: A. ,vol. 395, pp. 315- 322 ,(2005) , 10.1016/J.MSEA.2004.12.042
A. K. M. Aziz Ahamed, Hiroshi Kato, Influence of Casting Defects on Tensile Properties of ADC12 Aluminum Alloy Die-Castings Materials Transactions. ,vol. 49, pp. 1621- 1628 ,(2008) , 10.2320/MATERTRANS.F-MRA2008814
Giulio Timelli, Alberto Fabrizi, The Effects of Microstructure Heterogeneities and Casting Defects on the Mechanical Properties of High-Pressure Die-Cast AlSi9Cu3(Fe) Alloys Metallurgical and Materials Transactions A-physical Metallurgy and Materials Science. ,vol. 45, pp. 5486- 5498 ,(2014) , 10.1007/S11661-014-2515-7
Laihua Wang, Peter Turnley, Gary Savage, Gas content in high pressure die castings Journal of Materials Processing Technology. ,vol. 211, pp. 1510- 1515 ,(2011) , 10.1016/J.JMATPROTEC.2011.03.024
Qian Wan, Haidong Zhao, Chun Zou, Effect of Micro-porosities on Fatigue Behavior in Aluminum Die Castings by 3D X-ray Tomography Inspection Isij International. ,vol. 54, pp. 511- 515 ,(2014) , 10.2355/ISIJINTERNATIONAL.54.511