Conductive 3D microstructures by direct 3D printing of polymer/carbon nanotube nanocomposites via liquid deposition modeling
作者： Giovanni Postiglione , Gabriele Natale , Gianmarco Griffini , Marinella Levi , Stefano Turri
DOI: 10.1016/J.COMPOSITESA.2015.05.014
关键词:
摘要: … 3D printing technique is developed in this work for the fabrication of conductive 3D microstructures … of a low-cost commercial benchtop 3D printer equipped with a syringe dispenser (see …
core.ac.uk
sci-hub.se 参考文章(18)
J. F. Hutton, Kenneth Walters, Howard A. Barnes, An Introduction To Rheology ,(1989)
Brent Stucker, Ian Gibson, David W. Rosen, Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing ,(2009)
Diego Molina, Gianmarco Griffini, Marinella Levi, Stefano Turri, Novel conductive nanocomposites from perfluoropolyether waterborne polyurethanes and carbon nanotubes Polymers for Advanced Technologies. ,vol. 25, pp. 1082- 1088 ,(2014) , 10.1002/PAT.3354
Halil L. Tekinalp, Vlastimil Kunc, Gregorio M. Velez-Garcia, Chad E. Duty, Lonnie J. Love, Amit K. Naskar, Craig A. Blue, Soydan Ozcan, Highly oriented carbon fiber–polymer composites via additive manufacturing Composites Science and Technology. ,vol. 105, pp. 144- 150 ,(2014) , 10.1016/J.COMPSCITECH.2014.10.009
Vojislav Petrovic, Juan Vicente Haro Gonzalez, Olga Jordá Ferrando, Javier Delgado Gordillo, Jose Ramón Blasco Puchades, Luis Portolés Griñan, Additive Layer Manufacturing: State of the art in industrial applications through case studies International Journal of Production Research. ,vol. 49, pp. 1061- 1079 ,(2011) , 10.1080/00207540903479786
Sung-Il Moon, Fengzhe Jin, Cheol-jin Lee, Sadami Tsutsumi, Suong-Hyu Hyon, Novel Carbon Nanotube/Poly(L‐lactic acid) Nanocomposites; Their Modulus, Thermal Stability, and Electrical Conductivity Macromolecular Symposia. ,vol. 224, pp. 287- 296 ,(2005) , 10.1002/MASY.200550625
Simon J. Leigh, Robert J. Bradley, Christopher P. Purssell, Duncan R. Billson, David A. Hutchins, A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors PLOS ONE. ,vol. 7, ,(2012) , 10.1371/JOURNAL.PONE.0049365
Shuang-Zhuang Guo, Frédérick Gosselin, Nicolas Guerin, Anne-Marie Lanouette, Marie-Claude Heuzey, Daniel Therriault, Solvent‐Cast Three‐Dimensional Printing of Multifunctional Microsystems Small. ,vol. 9, pp. 4118- 4122 ,(2013) , 10.1002/SMLL.201300975
Bethany C. Gross, Jayda L. Erkal, Sarah Y. Lockwood, Chengpeng Chen, Dana M. Spence, Evaluation of 3D printing and its potential impact on biotechnology and the chemical sciences. Analytical Chemistry. ,vol. 86, pp. 3240- 3253 ,(2014) , 10.1021/AC403397R
Mario D Monzón, Ian Gibson, Antonio N Benítez, Luis Lorenzo, Pedro M Hernández, María D Marrero, None, Process and material behavior modeling for a new design of micro-additive fused deposition The International Journal of Advanced Manufacturing Technology. ,vol. 67, pp. 2717- 2726 ,(2013) , 10.1007/S00170-012-4686-Y