TiAlN based wear resistant coatings modified by molybdenum addition
作者： Łukasz Tomaszewski , Wojciech Gulbiński , Arkadiusz Urbanowicz , Tomasz Suszko , Ariel Lewandowski
DOI: 10.1016/J.VACUUM.2015.08.027
关键词:
摘要: Abstract TiAlN based coatings have been deposited by reactive vacuum arc evaporation combined with co-deposition of molybdenum from planar magnetron source. Obtained quasi-multilayer TiAlN/(TiAl)1−xMoxN structure was affected the specific deposition system geometry. An average content up to 8 at.%. The addition resulted in a significant improvement tribological properties manifesting itself lowering friction coefficient vs steel 0.8 down 0.5 and wear rate below 10−15 m3/Nm. Other mechanical like hardness adhesion remained unaffected or slightly improved. Observed change response for studied interpreted as being caused beneficial contribution lubricating oxides generated tribo-contact during process. Molybdenum also corrosion resistance. It an improved resistance pitting accompanied increase potential tested potentiodynamic method 0.5 M NaCl solution.
sci-hub.se 参考文章(34)
A. Kimura, H. Hasegawa, K. Yamada, T. Suzuki, Metastable Ti1−xAlxN films with different Al content Journal of Materials Science Letters. ,vol. 19, pp. 601- 602 ,(2000) , 10.1023/A:1006738514096
H. A. El Dahan, Pitting corrosion inhibition of 316 stainless steel in phosphoric acid-chloride solutions Part I Potentiodynamic and potentiostatic polarization studiess Journal of Materials Science. ,vol. 34, pp. 851- 857 ,(1999) , 10.1023/A:1004545501971
D.G. Sangiovanni, V. Chirita, L. Hultman, Toughness enhancement in TiAlN-based quarternary alloys Thin Solid Films. ,vol. 520, pp. 4080- 4088 ,(2012) , 10.1016/J.TSF.2012.01.030
Thomas Reeswinkel, Davide G. Sangiovanni, Valeriu Chirita, Lars Hultman, Jochen M. Schneider, Structure and mechanical properties of TiAlN–WNx thin films Surface & Coatings Technology. ,vol. 205, pp. 4821- 4827 ,(2011) , 10.1016/J.SURFCOAT.2011.04.066
Harish C. Barshilia, M. Surya Prakash, Anjana Jain, K.S. Rajam, Structure, hardness and thermal stability of TiAlN and nanolayered TiAlN/CrN multilayer films Vacuum. ,vol. 77, pp. 169- 179 ,(2005) , 10.1016/J.VACUUM.2004.08.020
Xing-zhao Ding, A.L.K. Tan, X.T. Zeng, C. Wang, T. Yue, C.Q. Sun, Corrosion resistance of CrAlN and TiAlN coatings deposited by lateral rotating cathode arc Thin Solid Films. ,vol. 516, pp. 5716- 5720 ,(2008) , 10.1016/J.TSF.2007.07.069
Kwang Ho Kim, Eun Young Choi, Seung Gyun Hong, Bong Gyu Park, Jae Hong Yoon, Jeong Hae Yong, Syntheses and mechanical properties of Cr–Mo–N coatings by a hybrid coating system Surface & Coatings Technology. ,vol. 201, pp. 4068- 4072 ,(2006) , 10.1016/J.SURFCOAT.2006.08.098
A. Biksa, K. Yamamoto, G. Dosbaeva, S.C. Veldhuis, G.S. Fox-Rabinovich, A. Elfizy, T. Wagg, L.S. Shuster, Wear behavior of adaptive nano-multilayered AlTiN/MexN PVD coatings during machining of aerospace alloys Tribology International. ,vol. 43, pp. 1491- 1499 ,(2010) , 10.1016/J.TRIBOINT.2010.02.008
M Pinkas, J Pelleg, M.P Dariel, Structural analysis of (Ti1-xAlx)N graded coatings deposited by reactive magnetron sputtering Thin Solid Films. ,vol. 355, pp. 380- 384 ,(1999) , 10.1016/S0040-6090(99)00667-7
C.J Tavares, L Rebouta, M Andritschky, F Guimarães, A Cavaleiro, Mechanical and surface analysis of Ti0.4Al0.6N/Mo multilayers Vacuum. ,vol. 60, pp. 339- 346 ,(2001) , 10.1016/S0042-207X(00)00413-9