Uncertainty of temperature measurements in dry orthogonal cutting of titanium alloys
作者： Daniel Soler , Patxi Aristimuño , Ainhara Garay , Pedro J. Arrazola
DOI: 10.1016/J.INFRARED.2015.04.001
关键词:
摘要: Abstract Infrared radiation thermometer is used to measure the temperature of tool during dry orthogonal cutting titanium alloys. The accuracy measured depends on several parameters such as experimental set-up, physical acquisition data system and characteristic tool. These are identified, their uncertainty estimated way they influence final discussed.
harvard.edu
elsevier.com
sci-hub.se 参考文章(23)
Barry N. Taylor, Guidelines for Evaluating and Expressing the Uncertainty of Nist Measurement Results ,(2017)
Fumihiro Sakuma, Susumu Hattori, Establishing a practical temperature standard by using a narrow-band radiation thermometer with a silicon detector 計量研究所報告. ,vol. 32, pp. 91- 97 ,(1983)
Navneet Khanna, Ainhara Garay, Luis M. Iriarte, Daniel Soler, Kuldip S. Sangwan, Pedro J. Arrazola, Effect of heat treatment conditions on the machinability of Ti64 and Ti54M alloys Procedia CIRP. ,vol. 1, pp. 477- 482 ,(2012) , 10.1016/J.PROCIR.2012.04.085
Peter Saunders, Propagation of uncertainty for non-linear calibration equations with an application in radiation thermometry Metrologia. ,vol. 40, pp. 93- 101 ,(2003) , 10.1088/0026-1394/40/2/315
R.C Dewes, E Ng, K.S Chua, P.G Newton, D.K Aspinwall, Temperature measurement when high speed machining hardened mould/die steel Journal of Materials Processing Technology. ,vol. 92, pp. 293- 301 ,(1999) , 10.1016/S0924-0136(99)00116-8
J Pujana, L del Campo, R B Pérez-Sáez, M J Tello, I Gallego, P J Arrazola, Radiation thermometry applied to temperature measurement in the cutting process Measurement Science and Technology. ,vol. 18, pp. 3409- 3416 ,(2007) , 10.1088/0957-0233/18/11/022
R M'Saoubi, C Le Calvez, B Changeux, J L Lebrun, Thermal and microstructural analysis of orthogonal cutting of a low alloyed carbon steel using an infrared—charge-coupled device camera technique Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. ,vol. 216, pp. 153- 165 ,(2002) , 10.1243/0954405021519807
M.A. Davies, T. Ueda, R. M'Saoubi, B. Mullany, A.L. Cooke, On The Measurement of Temperature in Material Removal Processes CIRP Annals. ,vol. 56, pp. 581- 604 ,(2007) , 10.1016/J.CIRP.2007.10.009
G. Sutter, L. Faure, A. Molinari, N. Ranc, V. Pina, An experimental technique for the measurement of temperature fields for the orthogonal cutting in high speed machining International Journal of Machine Tools & Manufacture. ,vol. 43, pp. 671- 678 ,(2003) , 10.1016/S0890-6955(03)00037-3
Daniel Soler, Thomas H. C. Childs, Pedro Jose Arrazola, A Note on Interpreting Tool Temperature Measurements from Thermography Machining Science and Technology. ,vol. 19, pp. 174- 181 ,(2015) , 10.1080/10910344.2014.991027