Surface modification by oil jet peening in Al alloys, AA6063-T6 and AA6061-T4
作者： A. Sahaya Grinspan , R. Gnanamoorthy
DOI: 10.1016/J.APSUSC.2005.12.164
关键词:
摘要: Abstract Oil jet peening is a new surface treatment technique that can be potentially applied to impart compressive residual stresses in metal parts. The effect of oil pressure on the integrity and texture metals are discussed. morphology, mass loss rate, indentation, erosion reported. With increasing stand-off distance, size indents significantly decreases reduces average roughness both specimens. Results also compared with other mechanical process such as shot peening, laser shock water peening.
harvard.edu
elsevier.com
sci-hub.se 参考文章(27)
Paul S. Prevey, John T. Cammett, The Effect of Shot Peening Coverage on Residual Stress, Cold Work and Fatigue in a Ni-Cr-Mo Low Alloy Steel Wiley‐VCH Verlag GmbH & Co. KGaA. pp. 295- 304 ,(2000) , 10.1002/3527606580.CH37
Hitoshi Soyama, Andrzej Lichtarowicz, Takahiro Momma, Edward J. Williams, A New Calibration Method for Dynamically Loaded Transducers and Its Application to Cavitation Impact Measurement Journal of Fluids Engineering-transactions of The Asme. ,vol. 120, pp. 712- 718 ,(1998) , 10.1115/1.2820728
M. Gerland, M. Hallouin, Effect of pressure on the microstructure of an austenitic stainless steel shock-loaded by very short laser pulses Journal of Materials Science. ,vol. 29, pp. 345- 351 ,(1994) , 10.1007/BF01162489
Takenori Shindo, Risaburo Oba, Ryoichiro Oshima, Masahiro Yamabe, Yoshiaki Yamauchi, Hitoshi Soyama, Yasunori Adachi, Kazunori Sato, Suitable Region of High-Speed Submerged Water Jets for Cutting and Peening. Jsme International Journal Series B-fluids and Thermal Engineering. ,vol. 38, pp. 31- 38 ,(1995) , 10.1299/JSMEB.38.31
A. Eftekhari, J.E. Talia, P.K. Mazumdar, Influence of surface condition on the fatigue of an aluminum-lithium alloy (2090-T3) Materials Science and Engineering: A. ,vol. 199, pp. L3- L6 ,(1995) , 10.1016/0921-5093(95)09805-4
Graham Hammersley, Lloyd A. Hackel, Fritz Harris, Surface prestressing to improve fatigue strength of components by laser shot peening Optics and Lasers in Engineering. ,vol. 34, pp. 327- 337 ,(2000) , 10.1016/S0143-8166(00)00083-X
A. Sahaya Grinspan, R. Gnanamoorthy, A novel surface modification technique for the introduction of compressive residual stress and preliminary studies on Al alloy AA6063 Surface and Coatings Technology. ,vol. 201, pp. 1768- 1775 ,(2006) , 10.1016/J.SURFCOAT.2006.03.002
Carolyn M. Preece, John H. Brunton, Richard F. Lawn, Liquid impact erosion of Al-Mg and Al-Cu alloys Wear. ,vol. 60, pp. 285- 304 ,(1980) , 10.1016/0043-1648(80)90228-8
Carolyn M. Preece, John H. Brunton, A comparison of liquid impact erosion and cavitation erosion Wear. ,vol. 60, pp. 269- 284 ,(1980) , 10.1016/0043-1648(80)90227-6
D.W. Hammond, S.A. Meguid, Crack propagation in the presence of shot-peening residual stresses Engineering Fracture Mechanics. ,vol. 37, pp. 373- 387 ,(1990) , 10.1016/0013-7944(90)90048-L