Comparison of scuffing life between unidirectional and reciprocating sliding motion
作者： D.H. Cho , Y.Z. Lee
DOI: 10.1016/J.WEAR.2010.12.032
关键词:
摘要: Abstract The objective of the present paper is to compare scuffing life and break-in effect between unidirectional sliding motion (USM) reciprocating (RSM). normalizing procedure on under different motions also was investigated. results our study showed that RSM had a disadvantage with regard resistance. These phenomena are related change in hardness distribution residual stress due procedure. Also, it found possible predict from trend-line immediate loading tests case as-received specimens. On other hand, normalized specimens there an important transition point magnitude early failure infinite surfaces life. Finally, observed has greater influence than USM
elsevier.com
sci-hub.se 参考文章(20)
J. Larsen-Badse, K.G. Mathew, Influence of structure on the abrasion resistance of a 1040 steel Wear. ,vol. 14, pp. 199- 205 ,(1969) , 10.1016/0043-1648(69)90041-6
Dae-Hyun Cho, Sung-Ae Lee, Young-Ze Lee, The Effects of Surface Roughness and Coatings on the Tribological Behavior of the Surfaces of a Piston Skirt Tribology Transactions. ,vol. 53, pp. 137- 144 ,(2009) , 10.1080/10402000903283276
Young-Ze Lee, Byung-Ju Kim, The influence of the boundary lubricating conditions of three different fluids on the plastic fatigue related mechanisms of wear and scuffing Wear. ,vol. 232, pp. 116- 121 ,(1999) , 10.1016/S0043-1648(99)00252-5
K. Mao, A new approach for polymer composite gear design Wear. ,vol. 262, pp. 432- 441 ,(2007) , 10.1016/J.WEAR.2006.06.005
Jin-Wook Kim, Young-Ze Lee, The residual stresses on lubricated sliding surfaces during break-in and up to scuffing Wear. ,vol. 251, pp. 985- 989 ,(2001) , 10.1016/S0043-1648(01)00701-3
Liu Jiajun, Lu Zhiqiang, Cheng Yinqian, The study of scuffing and pitting failure of cam-tappet rubbing pair Wear. ,vol. 140, pp. 135- 147 ,(1990) , 10.1016/0043-1648(90)90127-V
JOOJH Hershberger, OO Ajayi, J Zhang, H Yoon, GR Fenske, None, Formation of austenite during scuffing failure of SAE 4340 steel Wear. ,vol. 256, pp. 159- 167 ,(2004) , 10.1016/S0043-1648(03)00375-2
G.C. Barber, K.C. Ludema, The break-in stage of cylinder-ring wear: A correlation between fired engines and a laboratory simulator Wear. ,vol. 118, pp. 57- 75 ,(1987) , 10.1016/0043-1648(87)90005-6
Kitae Kim, Kenneth C. Ludema, A Correlation Between Low Cycle Fatigue Properties and Scuffing Properties of 4340 Steel Journal of Tribology. ,vol. 117, pp. 617- 621 ,(1995) , 10.1115/1.2831525
O.O. Ajayi, J.G. Hersberger, J. Zhang, H. Yoon, G.R. Fenske, Microstructural evolution during scuffing of hardened 4340 steel: implication for scuffing mechanism Tribology International. ,vol. 38, pp. 277- 282 ,(2005) , 10.1016/J.TRIBOINT.2004.08.011