Effects of cold rolling and heat treatment on microstructure and mechanical properties of AA 5052 aluminum alloy
作者： Bo WANG , Xian-hua CHEN , Fu-sheng PAN , Jian-jun MAO , Yong FANG
DOI: 10.1016/S1003-6326(15)63866-3
关键词:
摘要: … Cold rolling is an important process of wide aluminum alloy sheets. Rolling reduction and the following annealing temperature are two important parameters during the rolling process. …
sci-hub.se 参考文章(30)
J. Koike, M. Mabuchi, K. Higashi, In situ observation of partial melting in superplastic aluminum alloy composites at high temperatures Acta Metallurgica et Materialia. ,vol. 43, pp. 199- 206 ,(1995) , 10.1016/0956-7151(95)90275-9
Wei Wen, J.G. Morris, The effect of cold rolling and annealing on the serrated yielding phenomenon of AA5182 aluminum alloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 373, pp. 204- 216 ,(2004) , 10.1016/J.MSEA.2004.01.041
S.L. Xia, M. Ma, J.X. Zhang, W.X. Wang, W.C. Liu, Effect of heating rate on the microstructure, texture and tensile properties of continuous cast AA 5083 aluminum alloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 609, pp. 168- 176 ,(2014) , 10.1016/J.MSEA.2014.05.002
W.C Liu, C.-S Man, J.G Morris, Lattice rotation of the cube orientation to the β fiber during cold rolling of AA 5052 aluminum alloy Scripta Materialia. ,vol. 45, pp. 807- 814 ,(2001) , 10.1016/S1359-6462(01)01074-0
Tetsuo Sakai, Syuichi Hamada, Yoshihiro Saito, Improvement of the r-value in 5052 aluminum alloy sheets having through-thickness shear texture by 2-pass single-roll drive unidirectional shear rolling Scripta Materialia. ,vol. 44, pp. 2569- 2573 ,(2001) , 10.1016/S1359-6462(01)00932-0
S Gourdet, F Montheillet, An experimental study of the recrystallization mechanism during hot deformation of aluminium Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 283, pp. 274- 288 ,(2000) , 10.1016/S0921-5093(00)00733-4
W LIU, J MORRIS, Effect of hot and cold deformation on the β fiber rolling texture in continuous cast AA 5052 aluminum alloy Scripta Materialia. ,vol. 52, pp. 1317- 1321 ,(2005) , 10.1016/J.SCRIPTAMAT.2005.02.031
M. Ghosh, A. Miroux, L.A.I. Kestens, Correlating r-value and through thickness texture in Al–Mg–Si alloy sheets Journal of Alloys and Compounds. ,vol. 619, pp. 585- 591 ,(2015) , 10.1016/J.JALLCOM.2014.09.038
D.H. Liu, H.P. Yu, C.F. Li, Comparative study of the microstructure of 5052 aluminum alloy sheets under quasi-static and high-velocity tension Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 551, pp. 280- 287 ,(2012) , 10.1016/J.MSEA.2012.05.018
Fábio J.P. Simões, Ricardo J. Alves de Sousa, José J.A. Grácio, Frédéric Barlat, Jeong Whan Yoon, Mechanical behavior of an asymmetrically rolled and annealed 1050-O sheet International Journal of Mechanical Sciences. ,vol. 50, pp. 1372- 1380 ,(2008) , 10.1016/J.IJMECSCI.2008.07.009