Consolidation of Al particles through forward extrusion-equal channel angular pressing (FE-ECAP)
作者： M.H. Paydar , M. Reihanian , E. Bagherpour , M. Sharifzadeh , M. Zarinejad
DOI: 10.1016/J.MATLET.2008.02.038
关键词:
摘要: In the present study, aluminum particles are consolidated successfully by forward extrusion-equal channel angular pressing, referred as FE-ECAP process, at 200 °C. this method, two processes of extrusion (FE) and equal pressing (ECAP) occur subsequently in a single die. For comparison, powders also conventional same conditions process. The material shows fine grain structure with excellent mechanical properties relative to those obtained Advantages method can be expressed as: possibility performing die producing long bar samples full density from particles.
elsevier.com
sci-hub.se 参考文章(11)
S. XIANG, K. MATSUKI, N. TAKATSUJI, M. TOKIZAWA, T. YOKOTE, J. KUSUI, K. YOKOE, Microstructure and Mechanical Properties of PM 2024Al-3Fe-5Ni Alloy Consolidated by a New Process, Equal Channel Angular Pressing Journal of Materials Science Letters. ,vol. 16, pp. 1725- 1727 ,(1997) , 10.1023/A:1018511122362
Marek Galanty, Pawel Kazanowski, Panya Kansuwan, Wojciech Z Misiolek, Consolidation of metal powders during the extrusion process Journal of Materials Processing Technology. ,vol. 125, pp. 491- 496 ,(2002) , 10.1016/S0924-0136(02)00327-8
J. Robertson, J.-T. Im, I. Karaman, K.T. Hartwig, I.E. Anderson, Consolidation of amorphous copper based powder by equal channel angular extrusion Journal of Non-crystalline Solids. ,vol. 317, pp. 144- 151 ,(2003) , 10.1016/S0022-3093(02)01995-6
O.N. Senkov, S.V. Senkova, J.M. Scott, D.B. Miracle, Compaction of amorphous aluminum alloy powder by direct extrusion and equal channel angular extrusion Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 393, pp. 12- 21 ,(2005) , 10.1016/J.MSEA.2004.09.061
Si-Young Chang, Ki-Seung Lee, Seung-Hoe Choi, Dong Hyuk Shin, Effect of ECAP on microstructure and mechanical properties of a commercial 6061 Al alloy produced by powder metallurgy Journal of Alloys and Compounds. ,vol. 354, pp. 216- 220 ,(2003) , 10.1016/S0925-8388(03)00008-2
Y‐H Zhao, John F Bingert, X‐Z Liao, B‐Z Cui, Ke Han, Alla V Sergueeva, Amiys K Mukherjee, Ruslan Z Valiev, Terence G Langdon, Yuntian T Zhu, Simultaneously Increasing the Ductility and Strength of Ultra‐Fine‐Grained Pure Copper Advanced Materials. ,vol. 18, pp. 2949- 2953 ,(2006) , 10.1002/ADMA.200601472
Niels Hansen, Hall-Petch relation and boundary strengthening Scripta Materialia. ,vol. 51, pp. 801- 806 ,(2004) , 10.1016/J.SCRIPTAMAT.2004.06.002
D. Nagarajan, Chakkingal Uday, P. Venugopal, Microstructure and Mechanical Properties Resulting from Conventional Cold Extrusion of Equal Channel Angular Extruded Aluminium Alloy AA6101 Materials Science Forum. pp. 287- 292 ,(2006) , 10.4028/WWW.SCIENTIFIC.NET/MSF.503-504.287
Yoshinori Iwahashi, J Wang, Zenji Horita, Minoru Nemoto, Terence G Langdon, Principle of equal-channel angular pressing for the processing of ultra-fine grained materials Scripta Materialia. ,vol. 35, pp. 143- 146 ,(1996) , 10.1016/1359-6462(96)00107-8
D. Nagarajan, Uday Chakkingal, P. Venugopal, Influence of cold extrusion on the microstructure and mechanical properties of an aluminium alloy previously subjected to equal channel angular pressing Journal of Materials Processing Technology. ,vol. 182, pp. 363- 368 ,(2007) , 10.1016/J.JMATPROTEC.2006.08.016