Synthesis and Evaluation of TiC/Al3Ti Coating on Iron Via Thermal Explosion of Al-Ti-C System
作者： Q. Y. Zhang , Z. G. Zhao , W. Shi , L. Wang , X. H. Cui
DOI: 10.1007/S11665-013-0676-Y
关键词:
摘要: Thermal explosion reactions of Al-Ti-C system were studied. It was found that TiC and Al3Ti could be synthesized as final products in the system. A particular morphology variation occurred with an increase content. presented a strip form content 20 wt.%; TiC, its shape changed to granular reduced size. TiC-reinforced intermetallic matrix composite coating successfully fabricated on iron substrate by thermal during casting. As contents reached 20-40 wt.%, ignited fully completed molten achieve compacted good metallurgical bonding between basal iron. The elements Al, Ti, C, Fe gradiently distributed from matrix. hardness substantially higher than slightly increased relatively lower wear rates H13 steel at 25-400 °C.
springer.com
harvard.edu
sci-hub.se 参考文章(26)
E. Bahrami Motlagh, H. Nasiri, J. Vahdati Khaki, M. Haddad Sabzevar, Formation of metal matrix composite reinforced with Nano sized Al2O3+Ni-Al intermetallics during coating of Al substrate via combustion synthesis Surface & Coatings Technology. ,vol. 205, pp. 5515- 5520 ,(2011) , 10.1016/J.SURFCOAT.2011.06.026
H.M. Wang, G. Duan, Wear and corrosion behavior of laser clad Cr3Si reinforced intermetallic composite coatings Intermetallics. ,vol. 11, pp. 755- 762 ,(2003) , 10.1016/S0966-9795(03)00078-5
N Bertolino, U Anselmi-Tamburini, F Maglia, G Spinolo, Z.A Munir, Combustion synthesis of Zr–Si intermetallic compounds Journal of Alloys and Compounds. ,vol. 288, pp. 238- 248 ,(1999) , 10.1016/S0925-8388(99)00077-8
S.Q. Wang, M.X. Wei, Y.T. Zhao, Effects of the tribo-oxide and matrix on dry sliding wear characteristics and mechanisms of a cast steel Wear. ,vol. 269, pp. 424- 434 ,(2010) , 10.1016/J.WEAR.2010.04.028
Yisan Wang, Xinyuan Zhang, Fengchun Li, Guangting Zeng, Study on an Fe–TiC surface composite produced in situ Materials & Design. ,vol. 20, pp. 233- 236 ,(1999) , 10.1016/S0261-3069(98)00049-1
P Li, Preparation of Al–TiC composites by self-propagating high-temperature synthesis Scripta Materialia. ,vol. 49, pp. 699- 703 ,(2003) , 10.1016/S1359-6462(03)00402-0
M.X. Wei, S.Q. Wang, L. Wang, X.H. Cui, K.M. Chen, Effect of tempering conditions on wear resistance in various wear mechanisms of H13 steel Tribology International. ,vol. 44, pp. 898- 905 ,(2011) , 10.1016/J.TRIBOINT.2011.03.005
SQ Wang, XX Li, KM Chen, HJ Jin, None, TiC/Ni3Al coating on steel via combustion synthesis during casting Materials Letters. ,vol. 61, pp. 2531- 2534 ,(2007) , 10.1016/J.MATLET.2006.09.061
M. Yamaguchi, H. Inui, K. Ito, High-temperature structural intermetallics Acta Materialia. ,vol. 48, pp. 307- 322 ,(2000) , 10.1016/S1359-6454(99)00301-8
Haimin Ding, Xiangfa Liu, Lina Yu, Guoqun Zhao, The influence of forming processes on the distribution and morphologies of TiC in Al–Ti–C master alloys Scripta Materialia. ,vol. 57, pp. 575- 578 ,(2007) , 10.1016/J.SCRIPTAMAT.2007.06.028