Deformation behavior and processing maps of Ni3Al-based superalloy during isothermal hot compression
作者： Yuting Wu , Yongchang Liu , Chong Li , Xingchuan Xia , Yuan Huang
DOI: 10.1016/J.JALLCOM.2017.04.116
关键词:
摘要: Abstract To study the hot deformation behavior of Ni3Al-based alloy, compression tests were conducted in temperature range 1050–1250 °C with strain rates from 0.01 to 10 s−1. With increase and decrease rate, flow stress alloy would be decreased. Based on obtained constitutive equation, calculated values peak are good agreement experimental ones, activation energy is determined as 802.71 kJ/mol. Moreover, by dynamic material model (DMM), processing maps hot-deformed alloys established. It indicated that optimum parameters for studied correspond 1250 °C 0.1 s−1. Specimens deformed under conditions exhibit fine uniform grains, which a typical recrystallization (DRX) microstructure. The DRX degree could effectively enhanced rate.
sci-hub.se 参考文章(43)
Yongchang Liu, Chenxi Liu, Ferdinand Sommer, Eric Jan Mittemeijer, Martensite formation kinetics of substitutional Fe-0.7 at.%Al alloy under uniaxial compressive stress Acta Materialia. ,vol. 98, pp. 164- 174 ,(2015) , 10.1016/J.ACTAMAT.2015.07.028
Dao-Guang He, Y.C. Lin, Ming-Song Chen, Jian Chen, Dong-Xu Wen, Xiao-Min Chen, Effect of pre-treatment on hot deformation behavior and processing map of an aged nickel-based superalloy Journal of Alloys and Compounds. ,vol. 649, pp. 1075- 1084 ,(2015) , 10.1016/J.JALLCOM.2015.07.213
Jie Wu, Lei Xu, Zhengguan Lu, Bin Lu, Yuyou Cui, Rui Yang, Microstructure Design and Heat Response of Powder Metallurgy Ti2AlNb Alloys Journal of Materials Science & Technology. ,vol. 31, pp. 1251- 1257 ,(2015) , 10.1016/J.JMST.2015.09.006
H. Wu, S.P. Wen, H. Huang, X.L. Wu, K.Y. Gao, W. Wang, Z.R. Nie, Hot deformation behavior and constitutive equation of a new type Al–Zn–Mg–Er–Zr alloy during isothermal compression Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 651, pp. 415- 424 ,(2016) , 10.1016/J.MSEA.2015.10.122
Wojciech Polkowski, Ewa Pęczek, Dariusz Zasada, Zenon Komorek, Differential speed rolling of Ni3Al based intermetallic alloy – Effect of applied processing on structure and mechanical properties anisotropy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 647, pp. 170- 183 ,(2015) , 10.1016/J.MSEA.2015.08.083
NN Guo, L Wang, LS Luo, XZ Li, RR Chen, YQ Su, JJ Guo, HZ Fu, None, Hot deformation characteristics and dynamic recrystallization of the MoNbHfZrTi refractory high-entropy alloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 651, pp. 698- 707 ,(2016) , 10.1016/J.MSEA.2015.10.113
S. Tang, L.K. Ning, T.Z. Xin, Z. Zheng, Coarsening Behavior of Gamma Prime Precipitates in a Nickel Based Single Crystal Superalloy Journal of Materials Science & Technology. ,vol. 32, pp. 172- 176 ,(2016) , 10.1016/J.JMST.2015.10.005
H.J McQueen, N.D Ryan, Constitutive analysis in hot working Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 322, pp. 43- 63 ,(2002) , 10.1016/S0921-5093(01)01117-0
Hélio Goldenstein, Yuri Nunes Silva, Humberto N Yoshimura, None, Designing a new family of high temperature wear resistant alloys based on Ni3Al IC: experimental results and thermodynamic modelling Intermetallics. ,vol. 12, pp. 963- 968 ,(2004) , 10.1016/J.INTERMET.2004.02.027
Dong-Xu Wen, Y.C. Lin, Hong-Bin Li, Xiao-Min Chen, Jiao Deng, Lei-Ting Li, Hot deformation behavior and processing map of a typical Ni-based superalloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 591, pp. 183- 192 ,(2014) , 10.1016/J.MSEA.2013.09.049