High temperature nanoindentation – the importance of isothermal contact
作者： N.M. Everitt , M.I. Davies , J.F. Smith
DOI: 10.1080/14786435.2010.496745
关键词:
摘要: The suitability of high temperature techniques was investigated by finite element analysis modelling to give a qualitative view how the thermal picture develops under diamond indenter without controlled heating diamond. In case low-conductivity sample such as fused silica, gradient below tip is relatively diffuse, whereas with high-conductivity gold, most able equilibrate at set temperature, leading very steep in volume material that must accommodate deformation. However, both cases indentation occurring lower, and unknown, than bulk sample. results model are validated comparing obtained either indirectly contact or utilising separate heater for (an isothermal method). Nanoindentation presented experiments using cubic boron nitride Berko...
harvard.edu
sci-hub.se 参考文章(42)
Alexander Wanner, Oliver Kraft, Dagmar Saxa, Matthias Haag, The effect of temperature and strain rate on the hardness of Al and Al-based foams as measured by nanoindentation Zeitschrift Fur Metallkunde. ,vol. 92, pp. 1068- 1073 ,(2001)
Corinne E. Packard, Jan Schroers, Christopher A. Schuh, In situ measurements of surface tension-driven shape recovery in a metallic glass Scripta Materialia. ,vol. 60, pp. 1145- 1148 ,(2009) , 10.1016/J.SCRIPTAMAT.2009.02.056
B.D. Beake, J.F. Smith, A. Gray, G.S. Fox-Rabinovich, S.C. Veldhuis, J.L. Endrino, Investigating the correlation between nano-impact fracture resistance and hardness/modulus ratio from nanoindentation at 25–500 °C and the fracture resistance and lifetime of cutting tools with Ti1−xAlxN (x = 0.5 and 0.67) PVD coatings in milling operations Surface & Coatings Technology. ,vol. 201, pp. 4585- 4593 ,(2007) , 10.1016/J.SURFCOAT.2006.09.118
C L Wang, M Zhang, T G Nieh, Nanoindentation creep of nanocrystalline nickel at elevated temperatures Journal of Physics D. ,vol. 42, pp. 115405- ,(2009) , 10.1088/0022-3727/42/11/115405
G.S. Fox-Rabinovich, J.L. Endrino, B.D. Beake, M.H. Aguirre, S.C. Veldhuis, D.T. Quinto, C.E. Bauer, A.I. Kovalev, A. Gray, Effect of temperature of annealing below 900 °C on structure, properties and tool life of an AlTiN coating under various cutting conditions Surface & Coatings Technology. ,vol. 202, pp. 2985- 2992 ,(2008) , 10.1016/J.SURFCOAT.2007.10.034
Jason R. Trelewicz, Christopher A. Schuh, Hot nanoindentation of nanocrystalline Ni–W alloys Scripta Materialia. ,vol. 61, pp. 1056- 1059 ,(2009) , 10.1016/J.SCRIPTAMAT.2009.08.026
A. Richter, C.-L. Chen, R. Smith, E. McGee, R.C. Thomson, S.D. Kenny, Hot stage nanoindentation in multi-component Al–Ni–Si alloys: Experiment and simulation Materials Science and Engineering: A. ,vol. 494, pp. 367- 379 ,(2008) , 10.1016/J.MSEA.2008.04.057
B.D. Beake, G.S. Fox-Rabinovich, S.C. Veldhuis, S.R. Goodes, Coating optimisation for high speed machining with advanced nanomechanical test methods Surface & Coatings Technology. ,vol. 203, pp. 1919- 1925 ,(2009) , 10.1016/J.SURFCOAT.2009.01.025
D. E. Kramer, K. B. Yoder, W. W. Gerberich, Surface constrained plasticity: Oxide rupture and the yield point process Philosophical Magazine. ,vol. 81, pp. 2033- 2058 ,(2001) , 10.1080/01418610108216651
A. Sawant, S. Tin, High temperature nanoindentation of a Re-bearing single crystal Ni-base superalloy Scripta Materialia. ,vol. 58, pp. 275- 278 ,(2008) , 10.1016/J.SCRIPTAMAT.2007.10.013