A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis
作者： J.P. Davim , C. Maranhão
DOI: 10.1016/J.MATDES.2008.04.029
关键词:
摘要: Abstract The present paper employs the finite element method to determine plastic strain and rate when machining an AISI 1045 steel. A validation of process using literature experimental values was also conducted in order verify if obtained results with commercial software were close those found within literary research. comparison shows that modulation can be used either or special attention is taken into consideration analytical models. effect high speed (HSM) cutting steel observed. From simulations, it concluded both predicted good precision FEM model.
elsevier.com
sci-hub.se 参考文章(18)
A. I. Gnevko, N. A. Kazakov, D. V. Lazarev, V. V. Velichkovskii, Effect of the Loading Rate on the Microhardness of Metallic Materials and the Micromechanism of Plastic Strain Metal Science and Heat Treatment. ,vol. 44, pp. 448- 448 ,(2002) , 10.1023/A:1021964931024
A.G. Odeshi, S. Al-ameeri, M.N. Bassim, Effect of high strain rate on plastic deformation of a low alloy steel subjected to ballistic impact Journal of Materials Processing Technology. ,vol. 162, pp. 385- 391 ,(2005) , 10.1016/J.JMATPROTEC.2005.02.157
J.D. Puerta Velásquez, B. Bolle, P. Chevrier, G. Geandier, A. Tidu, Metallurgical study on chips obtained by high speed machining of a Ti–6 wt.%Al–4 wt.%V alloy Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 452, pp. 469- 474 ,(2007) , 10.1016/J.MSEA.2006.10.090
Jose C. Outeiro, Influence of tool sharpness on the thermal and mechanical phenomena generated during machining operations International Journal of Machining and Machinability of Materials. ,vol. 2, pp. 413- 432 ,(2007) , 10.1504/IJMMM.2007.015474
N.A. Abukhshim, P.T. Mativenga, M.A. Sheikh, Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 782- 800 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.07.024
R.S. Pawade, Suhas S. Joshi, P.K. Brahmankar, Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718 International Journal of Machine Tools and Manufacture. ,vol. 48, pp. 15- 28 ,(2008) , 10.1016/J.IJMACHTOOLS.2007.08.004
B. Denkena, R. Ben Amor, L. De Leon Garcia, J. Dege, Material specific definition of the high speed cutting range International Journal of Machining and Machinability of Materials. ,vol. 2, pp. 176- 185 ,(2007) , 10.1504/IJMMM.2007.013781
Amos Gilat, Xinrong Wu, Plastic deformation of 1020 steel over a wide range of strain rates and temperatures International Journal of Plasticity. ,vol. 13, pp. 611- 632 ,(1997) , 10.1016/S0749-6419(97)00028-4
C.Z. Duan, M.J. Wang, J.Z. Pang, G.H. Li, A calculational model of shear strain and strain rate within shear band in a serrated chip formed during high speed machining Journal of Materials Processing Technology. ,vol. 178, pp. 274- 277 ,(2006) , 10.1016/J.JMATPROTEC.2006.04.008
Q. Xue, X.Z. Liao, Y.T. Zhu, G.T. Gray, Formation mechanisms of nanostructures in stainless steel during high-strain-rate severe plastic deformation Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 410, pp. 252- 256 ,(2005) , 10.1016/J.MSEA.2005.08.022