Two-steps clinching of aluminum and Carbon Fiber Reinforced Polymer sheets
作者： Francesco Lambiase , Dae-Cheol Ko
DOI: 10.1016/J.COMPSTRUCT.2016.12.072
关键词:
摘要: Abstract The present paper investigates the effectiveness of two-steps clinching for joining aluminum and Carbon Fiber Reinforced Polymer (CFRP). To this end, different reshaping tools were involved after by with split dies. force was also varied. Single lap shear tests simple clinched reshaped specimens performed to determine influence process conditions on mechanical behavior joints. morphology geometry joints analyzed understand how step influences main quality criteria damage produced CFRP sheet. According experimental results, connection failed pullout; thus, critical parameter undercut. method, using optimized enabled increase strength 32%. Such an improvement due in undercut that resulted from a higher improved material flow. defects may appear these have been identified as well their causes.
elsevier.com
sci-hub.se 参考文章(42)
Nikolai Kashaev, Volker Ventzke, Stefan Riekehr, Falk Dorn, Manfred Horstmann, Assessment of alternative joining techniques for Ti–6Al–4V/CFRP hybrid joints regarding tensile and fatigue strength Materials & Design. ,vol. 81, pp. 73- 81 ,(2015) , 10.1016/J.MATDES.2015.04.051
Fanmao Meng, Wanxin Li, Hualin Fan, Yinzhi Zhou, A nonlinear theory for CFRP strengthened aluminum beam Composite Structures. ,vol. 131, pp. 574- 577 ,(2015) , 10.1016/J.COMPSTRUCT.2015.06.022
Howard Kuhn, Dana Medlin, Mechanical testing and evaluation ASM International. ,(2000)
F. Lambiase, Mechanical behaviour of polymer–metal hybrid joints produced by clinching using different tools Materials & Design. ,vol. 87, pp. 606- 618 ,(2015) , 10.1016/J.MATDES.2015.08.037
Chan-Joo Lee, Jung-Min Lee, Ho-Yeon Ryu, Kyung-Hun Lee, Byung-Min Kim, Dae-Cheol Ko, Design of hole-clinching process for joining of dissimilar materials – Al6061-T4 alloy with DP780 steel, hot-pressed 22MnB5 steel, and carbon fiber reinforced plastic Journal of Materials Processing Technology. ,vol. 214, pp. 2169- 2178 ,(2014) , 10.1016/J.JMATPROTEC.2014.03.032
C.G. Pickin, K. Young, I. Tuersley, Joining of lightweight sandwich sheets to aluminium using self-pierce riveting Materials & Design. ,vol. 28, pp. 2361- 2365 ,(2007) , 10.1016/J.MATDES.2006.08.003
Ryosuke Matsuzaki, Motoko Shibata, Akira Todoroki, Improving performance of GFRP/aluminum single lap joints using bolted/co-cured hybrid method Composites Part A: Applied Science and Manufacturing. ,vol. 39, pp. 154- 163 ,(2008) , 10.1016/J.COMPOSITESA.2007.11.009
Jacek Mucha, The effect of material properties and joining process parameters on behavior of self-pierce riveting joints made with the solid rivet Materials & Design. ,vol. 52, pp. 932- 946 ,(2013) , 10.1016/J.MATDES.2013.06.037
Jacek Mucha, Waldemar Witkowski, The experimental analysis of the double joint type change effect on the joint destruction process in uniaxial shearing test Thin-walled Structures. ,vol. 66, pp. 39- 49 ,(2013) , 10.1016/J.TWS.2013.01.018
S.M. Goushegir, J.F. dos Santos, S.T. Amancio-Filho, Friction Spot Joining of aluminum AA2024/carbon-fiber reinforced poly(phenylene sulfide) composite single lap joints: Microstructure and mechanical performance Materials & Design (1980-2015). ,vol. 54, pp. 196- 206 ,(2014) , 10.1016/J.MATDES.2013.08.034