Correlation between ultimate tensile strength and solidification microstructure for the sand cast A357 aluminium alloy
作者： L. Ceschini , Alessandro Morri , Andrea Morri , A. Gamberini , S. Messieri
DOI: 10.1016/J.MATDES.2009.05.012
关键词:
摘要: … aluminium alloy, in the sand cast and T6 heat treated condition. … The alloy was sand cast to produce cylinder heads and … machined from the cast components and cast separately. Some …
elsevier.com
sci-hub.se 参考文章(22)
Murat Tiryakioğlu, John Campbell, James T Staley, On macrohardness testing of Al–7 wt.% Si–Mg alloys: II. An evaluation of models for hardness–yield strength relationships Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 361, pp. 240- 248 ,(2003) , 10.1016/S0921-5093(03)00514-8
S. G. Shabestari, F. Shahri, Influence of modification, solidification conditions and heat treatment on the microstructure and mechanical properties of A356 aluminum alloy Journal of Materials Science. ,vol. 39, pp. 2023- 2032 ,(2004) , 10.1023/B:JMSC.0000017764.20609.0D
X ZHU, A SHYAM, J JONES, H MAYER, J LASECKI, J ALLISON, Effects of microstructure and temperature on fatigue behavior of E319-T7 cast aluminum alloy in very long life cycles International Journal of Fatigue. ,vol. 28, pp. 1566- 1571 ,(2006) , 10.1016/J.IJFATIGUE.2005.04.016
E Ogris, A Wahlen, H Lüchinger, P.J Uggowitzer, On the silicon spheroidization in Al-Si alloys Journal of Light Metals. ,vol. 2, pp. 263- 269 ,(2002) , 10.1016/S1471-5317(03)00010-5
M Tiryakioǧlu, J Campbell, J.T Staley, The influence of structural integrity on the tensile deformation of cast Al-7wt.%Si-0.6wt.%Mg alloys Scripta Materialia. ,vol. 49, pp. 873- 878 ,(2003) , 10.1016/S1359-6462(03)00439-1
Q. G. Wang, Microstructural Effects on the Tensile and Fracture Behavior of Aluminum Casting Alloys A356/357 Metallurgical and Materials Transactions A-physical Metallurgy and Materials Science. ,vol. 34, pp. 2887- 2899 ,(2003) , 10.1007/S11661-003-0189-7
L. Ceschini, A. Morri, G. Sambogna, The effect of hot isostatic pressing on the fatigue behaviour of sand-cast A356-T6 and A204-T6 aluminum alloys Journal of Materials Processing Technology. ,vol. 204, pp. 231- 238 ,(2008) , 10.1016/J.JMATPROTEC.2007.11.067
QG Wang, CH Cáceres, None, The fracture mode in Al–Si–Mg casting alloys Materials Science and Engineering: A. ,vol. 241, pp. 72- 82 ,(1998) , 10.1016/S0921-5093(97)00476-0
Z Li, A.M Samuel, F.H Samuel, C Ravindran, S Valtierra, H.W Doty, Parameters controlling the performance of AA319-type alloys: Part I. Tensile properties Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 367, pp. 96- 110 ,(2004) , 10.1016/J.MSEA.2003.09.090
T. Fukui, J.Z. Yi, P.D. Lee, T.C. Lindley, Statistical modeling of microstructure and defect population effects on the fatigue performance of cast A356-T6 automotive components Materials Science and Engineering: A. ,vol. 432, pp. 59- 68 ,(2006) , 10.1016/J.MSEA.2006.07.003