Stress Concentration Factor for a Flat Platewith Fillets and Notches under Axial LoadUsing ANSYS Software
作者： Jose MiguelGarcia Guzman , Francisco JavierOrtega Herrera , Alfonso Lozano Luna , Francisco JavierPalacios Díaz , Diego ArmandoGarcia Salazar
DOI: 10.15680/IJIRSET.2015.0405077
关键词:
摘要: This paper analyzes the stress concentration factor in a flat plate with two fillets and notches under an axial load. The maximum are calculated using ANSYS® software. These stresses used to determine for relations W/w = 1.2, 1.5, 2.0, 2.5, 3.0 terms of ratio r/L. factors obtained plotted as function r/L.The results show that r/Lratio does not have much effect on factor. Meanwhile, decreases r/L increases. Finally, least squares method is sixth grade polynomial equations can be at fillet study.
rroij.com参考文章(17)
José E. Martínez Ordaz, Jorge Carrera Bolaños, Luis A. Ferrer Argote, Análisis experimental y numérico de esfuerzos en placas con orificio circular bajo un gradiente de carga lineal Ingeniería Mecánica. Tecnología y Desarrollo. ,vol. 2, pp. 63- 68 ,(2006)
Uriel Bastidas, Fernando Roldan, Estudio Experimental y por Análisis de Elementos Finitos del Factor de Concentrador de Esfuerzo Producido por un Agujero en una Placa Plana Dyna. ,vol. 69, pp. 1- 8 ,(2002)
Milagros Sánchez Álvarez, Factor teórico de concentración de esfuerzos en placas anisotrópicas Universidad, Ciencia y Tecnología. ,vol. 10, pp. 168- 171 ,(2006)
N NODA, Y TAKASE, Stress concentration formula useful for all notch shape in a round bar (comparison between torsion, tension and bending) International Journal of Fatigue. ,vol. 28, pp. 151- 163 ,(2006) , 10.1016/J.IJFATIGUE.2005.04.015
Rumman Ul Ahsan, Protyasha Prachurja, Abu Raihan Mohammad Ali, Mohammad Arif Hasan Mamun, Determination of effect of elliptic notches and grooves on stress concentration factors on notched bar in tension and grooved shaft under torsion Journal of Naval Architecture and Marine Engineering. ,vol. 10, pp. 25- 32 ,(2013) , 10.3329/JNAME.V10I1.13675
H. Ou, B. Lu, Z. S. Cui, C. Lin, A direct shape optimization approach for contact problems with boundary stress concentration Journal of Mechanical Science and Technology. ,vol. 27, pp. 2751- 2759 ,(2013) , 10.1007/S12206-013-0721-7
Feras Darwish, Ghassan Tashtoush, Mohammad Gharaibeh, Stress concentration analysis for countersunk rivet holes in orthotropic plates European Journal of Mechanics A-solids. ,vol. 37, pp. 69- 78 ,(2013) , 10.1016/J.EUROMECHSOL.2012.04.006
FJ Gómez, M Elices, F Berto, P Lazzarin, None, A generalised notch stress intensity factor for U-notched components loaded under mixed mode Engineering Fracture Mechanics. ,vol. 75, pp. 4819- 4833 ,(2008) , 10.1016/J.ENGFRACMECH.2008.07.001
Guangyan Liu, Kaili Tang, Study on stress concentration in notched cross-ply laminates under tensile loading Journal of Composite Materials. ,vol. 50, pp. 283- 296 ,(2016) , 10.1177/0021998315573802
F O Sonmez, Optimal shape design of shoulder fillets for flat and round bars under various loadings Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. ,vol. 223, pp. 1741- 1754 ,(2009) , 10.1243/09544062JMES1457