Constructal optimization of cylindrical heat sources surrounded with a fin based on minimization of hot spot temperature
作者： Shuwen Gong , Lingen Chen , Huijun Feng , Zhihui Xie , Fengrui Sun
DOI: 10.1016/J.ICHEATMASSTRANSFER.2015.08.004
关键词:
摘要: Abstract Based on constructal theory, the construct of a three-dimensional cylindrical heat sources with convection transfer is investigated in this paper. The source model composed several surrounded fin or conical fin. not only exists generating electronic component to enhance transfer, but also fuel rod zircaloy cladding. For specified volumes and sources, optimized by taking minimization dimensionless hot spot temperature as optimization objective. results show that effectively reduced after optimization, which will provider some theoretical guidelines for optimal design system.
elsevier.com
sci-hub.se 参考文章(52)
Adrian Bejan, Constructal-theory network of conducting paths for cooling a heat generating volume International Journal of Heat and Mass Transfer. ,vol. 40, pp. 799- 816 ,(1997) , 10.1016/0017-9310(96)00175-5
M.R. Hajmohammadi, S.S. Nourazar, On the insertion of a thin gas layer in micro cylindrical Couette flows involving power-law liquids International Journal of Heat and Mass Transfer. ,vol. 75, pp. 97- 108 ,(2014) , 10.1016/J.IJHEATMASSTRANSFER.2014.03.065
L.G. Page, T. Bello-Ochende, J.P. Meyer, Constructal multi scale cylinders with rotation cooled by natural convection International Journal of Heat and Mass Transfer. ,vol. 57, pp. 345- 355 ,(2013) , 10.1016/J.IJHEATMASSTRANSFER.2012.10.048
Lotfollah Ghodoossi, Nilüfer Eǧrican, None, Conductive cooling of triangular shaped electronics using constructal theory Energy Conversion and Management. ,vol. 45, pp. 811- 828 ,(2004) , 10.1016/S0196-8904(03)00190-0
Mohammad Reza Hajmohammadi, Antonio Campo, S. Salman Nourazar, Amir Masood Ostad, Improvement of Forced Convection Cooling Due to the Attachment of Heat Sources to a Conducting Thick Plate Journal of Heat Transfer. ,vol. 135, pp. 124504- ,(2013) , 10.1115/1.4024897
Adrian Bejan, Alex J. Fowler, George Stanescu, The optimal spacing between horizontal cylinders in a fixed volume cooled by natural convection International Journal of Heat and Mass Transfer. ,vol. 38, pp. 2047- 2055 ,(1995) , 10.1016/0017-9310(94)00312-J
Marc Joucaviel, Louis Gosselin, Tunde Bello-Ochende, Maximum heat transfer density with rotating cylinders aligned in cross-flow International Communications in Heat and Mass Transfer. ,vol. 35, pp. 557- 564 ,(2008) , 10.1016/J.ICHEATMASSTRANSFER.2007.12.005
M.R. Hajmohammadi, M.R. Salimpour, M. Saber, A. Campo, Detailed analysis for the cooling performance enhancement of a heat source under a thick plate Energy Conversion and Management. ,vol. 76, pp. 691- 700 ,(2013) , 10.1016/J.ENCONMAN.2013.08.016
T. Bello-Ochende, A. Bejan, Constructal multi-scale cylinders with natural convection International Journal of Heat and Mass Transfer. ,vol. 48, pp. 4300- 4306 ,(2005) , 10.1016/J.IJHEATMASSTRANSFER.2005.05.023
Mohammad Reza Salimpour, Amir Menbari, Analytical optimization of constructal channels used for cooling a ring shaped body based on minimum flow and thermal resistances Energy. ,vol. 81, pp. 645- 651 ,(2015) , 10.1016/J.ENERGY.2015.01.008