Effect of Machining Parameters on Cutting Forces and Surface Roughness in Al-(1-2) Fe-1V-1Si Alloys
作者： B. N. Pathak , K. L. Sahoo , Madhawanand Mishra
DOI: 10.1080/10426914.2013.763952
关键词:
摘要: Two Al-alloys with compositions Al-1Fe-1V-1Si and Al-2Fe-1V-1Si were cast in the form of plates to study machinability. The paper deals effect Fe on machinability Al-Fe-V-Si alloys subjected milling operation using high speed steel end cutting tool. results show that force increases increasing depth cut feed rate, decreases speed. From experimental results, it is observed most significantly affected by cut, followed rate studies also underline fact surface finish improves decrease an increase optimum zone lies range 125 175 m/min for machining above Al alloys, where forces are almost independent High speed, low recommended better finish. chips formed observed. It as content i...
sci-hub.se 参考文章(13)
Hasan Gökkaya, The Effects of Machining Parameters on Cutting Forces, Surface Roughness, Built-Up Edge (BUE) and Built-Up Layer (BUL) During Machining AA2014 (T4) Alloy Strojniski Vestnik-journal of Mechanical Engineering. ,vol. 56, pp. 584- 593 ,(2010) , 10.5545/140_DOI_NOT_ASSIGNED
Ram Naresh Rai, G.L. Datta, M. Chakraborty, A.B. Chattopadhyay, A study on the machinability behaviour of Al–TiC composite prepared by in situ technique Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 428, pp. 34- 40 ,(2006) , 10.1016/J.MSEA.2005.11.040
Rajesh Kumar Bhushan, Sudhir Kumar, S Das, None, Effect of machining parameters on surface roughness and tool wear for 7075 Al alloy SiC composite The International Journal of Advanced Manufacturing Technology. ,vol. 50, pp. 459- 469 ,(2010) , 10.1007/S00170-010-2529-2
K.L. Sahoo, B.N. Pathak, Solidification behaviour, microstructure and mechanical properties of high Fe-containing Al–Si–V alloys Journal of Materials Processing Technology. ,vol. 209, pp. 798- 804 ,(2009) , 10.1016/J.JMATPROTEC.2008.02.043
T. J. Skingle, R. W. Thompson, Machining of aluminum alloys Journal of Applied Metalworking. ,vol. 1, pp. 76- 78 ,(1980) , 10.1007/BF02833612
T. Tanaka, T. Akasawa, Machinability of hypereutectic silicon-aluminum alloys Journal of Materials Engineering and Performance. ,vol. 8, pp. 463- 468 ,(1999) , 10.1361/105994999770346774
M. Alauddin, M.A. Mazid, M.A. El Baradi, M.S.J. Hashmi, Cutting forces in the end milling of Inconel 718 Journal of Materials Processing Technology. ,vol. 77, pp. 153- 159 ,(1998) , 10.1016/S0924-0136(97)00412-3
T. M. El-Hossainy, A. A. El-Zoghby, M. A. Badr, K. Y. Maalawi, M. F. Nasr, Cutting Parameter Optimization when Machining Different Materials Materials and Manufacturing Processes. ,vol. 25, pp. 1101- 1114 ,(2010) , 10.1080/10426914.2010.480998
S.K. Das, P.S. Gilman, D. Raybould, Applications of Rapidly Solidified High Temperature Aluminum Alloys Key Engineering Materials. ,vol. 38-39, pp. 367- 392 ,(1990) , 10.4028/WWW.SCIENTIFIC.NET/KEM.38-39.367
Soumya Gangopadhyay, Ranadip Acharya, Ajay Kumar Chattopadhyay, Vikas Gulabrao Sargade, EFFECT OF CUTTING SPEED AND SURFACE CHEMISTRY OF CUTTING TOOLS ON THE FORMATION OF BUL OR BUE AND SURFACE QUALITY OF THE GENERATED SURFACE IN DRY TURNING OF AA6005 ALUMINIUM ALLOY Machining Science and Technology. ,vol. 14, pp. 208- 223 ,(2010) , 10.1080/10910344.2010.500961