Electronmetallography of diamond cutting tools
S Karagoz , Muzaffer Zeren
Industrial Diamond Review ( 1) 40 -41
1
2003
Stress relaxation behaviour of thermomechanically heat treated cold drawn steel wires
Erdinç Kaluç , Adalet Zeren , Muzaffer Zeren , Kutsal Tulbentci
Wire industry 65 ( 771) 313 -316
1
1998
Alümina Katkılı ve Nikel ile Alaşımlandırılmış Alüminyum Esaslı Kompozitlerde Özelliklerin Karakterizasyonu
Muzaffer Zeren , Rıdvan Yamanoğlu , Nurgül Sak
Kocaeli Üniversitesi Fen Bilimleri Dergisi 1 ( 1) 1 -7
2018
The microstructural design of diamond cutting tools
Şadi Karagöz , Muzaffer Zeren
Materials Characterization 47 ( 2) 89 -91
16
2001
Effect of Cu content on the corrosion of Al‐Si eutectic alloys in acidic solutions
Sibel Zor , Muzaffer Zeren , Hatice Ozkazanc , Erdem Karakulak
Anti-corrosion Methods and Materials 57 ( 4) 185 -191
21
2010
Laser parameters optimization of surface treating of Al 6082-T6 with Taguchi method
Timur Canel , Muzaffer Zeren , Tamer Sınmazçelik
Optics and Laser Technology 120 105714
12
2019
The property optimization of diamond-cutting tools with the help of micro-structural characterization
Şadi Karagöz , Muzaffer Zeren
International Journal of Refractory Metals and Hard Materials 19 ( 1) 23 -26
11
2001
The effect of heat-treatment on aluminum-based piston alloys
Muzaffer Zeren
Materials & Design 28 ( 9) 2511 -2517
87
2007
Sintering of polycrystalline diamond cutting tools
Muzaffer Zeren , Şadi Karagöz
Materials & Design 28 ( 3) 1055 -1058
107
2007
Investigation of corrosion behaviors in chloride solutions of G-X 10CrNiMoNb 18-10 austenitic stainless steel produced by different casting techniques
Sibel Zor , Muzaffer Zeren , Levon Çapan , Mehmet Türker
Protection of Metals and Physical Chemistry of Surfaces 48 ( 2) 270 -274
2012
Influence of Ti addition on the microstructure and hardness properties of near-eutectic Al–Si alloys
Muzaffer Zeren , Erdem Karakulak
Journal of Alloys and Compounds 450 ( 1) 255 -259
98
2008
Effect of heat treatment on the tribological properties of Al-Cu-Mg/nanoSiC composites
Rıdvan Yamanoğlu , Erdem Karakulak , Adalet Zeren , Muzaffer Zeren
Materials & Design 49 820 -825
21
2013
Defect characterization in the diamond cutting tools
Muzaffer Zeren , Şadi Karagöz
Materials Characterization 57 ( 2) 111 -114
14
2006
Instrumented indentation and scratch testing evaluation of tribological properties of tin-based bearing materials
Mustafa Özgür Bora , Onur Coban , Tamer Sinmazcelik , Volkan Günay
Materials & Design 31 ( 6) 2707 -2715
18
2010
The effect of Zr on aging kinetics and properties of as-cast AA6082 alloy
Fulya Kahrıman , Muzaffer Zeren
International Journal of Metalcasting 11 ( 2) 216 -222
5
2017
Study on hardness and microstructural characteristics of sand cast Al-Si-Cu alloys
Muzaffer Zeren , Erdem Karakulak
Bulletin of Materials Science 32 ( 6) 617 -620
6
2009
Examination of Microstructure and Wear Behaviour of a Roller Material Produced by Centrifugal Casting
Onur Birbaşar , Ş. Hakan Atapek , Enbiya Türedi , Muzaffer Zeren
Materials Testing 54 ( 6) 421 -426
1
2012
Failure Analysis of a Hardened Steel Clamping Head
Ş. Hakan Atapek , Muzaffer Zeren , Fulya Kahrıman
Materials Testing 55 ( 11-12) 840 -844
2013
Mechanical properties of hypoeutectic Al-Ni alloys with Al3Ni intermetallics
Erdem Karakulak , Funda Gül Koç , Rıdvan Yamanoglu , Muzaffer Zeren
Materials Testing 58 ( 2) 117 -121
6
2016
Dry sliding wear behaviour of cast roller materials
Onur Birbaşar , Enbiya Türedi , Ş. Hakan Atapek , Muzaffer Zeren
International Journal of Surface Science and Engineering 9 253
1
2015