A hybrid approach of Taguchi-Response Surface Methodology for modeling and optimization of Duplex Turning process
作者： Ravindra Nath Yadav
DOI: 10.1016/J.MEASUREMENT.2016.12.060
关键词: Surface finish 、 Manufacturing engineering 、 Surface roughness 、 Cutting tool 、 Machining 、 Taguchi methods 、 High-speed steel 、 Duplex (telecommunications) 、 Mechanical engineering 、 Response surface methodology 、 Engineering
摘要: Abstract Productivity is always an important factor related to the industries for achieving higher production rate with better quality at low cost. In this respect, effort has been made improve productivity of turning process application two cutting tools in place single tool and such developed named as Duplex Turning. Due simultaneous on a shared rotating surface, Turning becomes more complex. complexity, selection suitable combination parameters difficult task manufacturer. The aims present paper are develop mathematical model optimize during alloy steel (AISI 1040) point high speed steel. experiments were performed Center Lathe Machine, which equipped setup. effect velocity, feed rate, primary depth-of-cut secondary analyzed average surface roughness. hybrid approach Taguchi Methodology-Response Surface Methodology (TM-RSM) applied due their potential modeling optimization complex machining process. optimum condition obtained from TM used central value RSM optimization. result shows significant improvement finish compared analysis.
sci-hub.se 参考文章(22)
Mikell P. Groover, Fundamentals of modern manufacturing : materials, processes, and systems J. Wiley. ,(1996)
J.S. Dureja, Rupinder Singh, Manpreet S. Bhatti, Optimizing flank wear and surface roughness during hard turning of AISI D3 steel by Taguchi and RSM methods Production and Manufacturing Research: An Open Access Journal. ,vol. 2, pp. 767- 783 ,(2014) , 10.1080/21693277.2014.955216
Sanjeev Saini, Inderpreet Singh Ahuja, Vishal S. Sharma, Modelling the effects of cutting parameters on residual stresses in hard turning of AISI H11 tool steel The International Journal of Advanced Manufacturing Technology. ,vol. 65, pp. 667- 678 ,(2013) , 10.1007/S00170-012-4206-0
Ashok Kumar Sahoo, Bidyadhar Sahoo, Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-II (RSM, grey relational and techno economical approach) Measurement. ,vol. 46, pp. 2868- 2884 ,(2013) , 10.1016/J.MEASUREMENT.2012.09.023
E. Aslan, Experimental investigation of cutting tool performance in high speed cutting of hardened X210 Cr12 cold-work tool steel (62 HRC) Materials & Design. ,vol. 26, pp. 21- 27 ,(2005) , 10.1016/J.MATDES.2004.04.004
Behnam Davoodi, Behzad Eskandari, Tool wear mechanisms and multi-response optimization of tool life and volume of material removed in turning of N-155 iron-nickel-base superalloy using RSM Measurement. ,vol. 68, pp. 286- 294 ,(2015) , 10.1016/J.MEASUREMENT.2015.03.006
D.K. Sarma, U.S. Dixit, A comparison of dry and air-cooled turning of grey cast iron with mixed oxide ceramic tool Journal of Materials Processing Technology. ,vol. 190, pp. 160- 172 ,(2007) , 10.1016/J.JMATPROTEC.2007.02.049
W. Grzesik, Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools Wear. ,vol. 265, pp. 327- 335 ,(2008) , 10.1016/J.WEAR.2007.11.001
Dilbag Singh, P Venkateswara Rao, None, A surface roughness prediction model for hard turning process The International Journal of Advanced Manufacturing Technology. ,vol. 32, pp. 1115- 1124 ,(2007) , 10.1007/S00170-006-0429-2
İlhan Asiltürk, Süleyman Neşeli, Multi response optimisation of CNC turning parameters via Taguchi method-based response surface analysis Measurement. ,vol. 45, pp. 785- 794 ,(2012) , 10.1016/J.MEASUREMENT.2011.12.004