Application of a Tough Surface Layer to a Fiber‐Bonded Composite
作者： Yeongseok Kim , Yutaka Kagawa , Shijie Zhu
DOI: 10.1111/J.1151-2916.2003.TB03525.X
关键词: Composite material 、 Surface layer 、 Stress concentration 、 Indentation 、 Sintering 、 Hot pressing 、 Layer (electronics) 、 Materials science 、 Composite number 、 Ceramic
摘要: The feasibility of creating tough surface material using oxide-fiber-reinforced oxide matrix ceramics was studied. Al 2 OI 3 fiber/(ZrO , O ) composite used as the a Si-Ti-C-O-fiber-bonded composite. sintering (ZrO and layer (SCL) its bonding to fiber-bonded (FBC) were done simultaneously by vacuum hot pressing. A spherical indentation test demonstrated advantage SCL in reducing damage base FBC from an indenter, because high fracture resistance could reduce stress concentration cumulative microfracture process.
sci-hub.se 参考文章(11)
Larry P. Zawada, Longitudinal and Transthickness Tensile Behavior of Several Oxide/Oxide Composites 22nd Annual Conference on Composites, Advanced Ceramics, Materials, and Structures: A: Ceramic Engineering and Science Proceedings, Volume 19, Issue 3. pp. 327- 339 ,(2008) , 10.1002/9780470294482.CH36
T. Ishikawa, A Tough, Thermally Conductive Silicon Carbide Composite with High Strength up to 1600°C in Air Science. ,vol. 282, pp. 1295- 1297 ,(1998) , 10.1126/SCIENCE.282.5392.1295
Carlos G. Levi, James Y. Yang, Brian J. Dalgleish, Frank W. Zok, Anthony G. Evans, Processing and Performance of an All‐Oxide Ceramic Composite Journal of the American Ceramic Society. ,vol. 81, pp. 2077- 2086 ,(2005) , 10.1111/J.1151-2916.1998.TB02590.X
F.F. Lange, W.C. Tu, A.G. Evans, Processing of damage-tolerant, oxidation-resistant ceramic matrix composites by a precursor infiltration and pyrolysis method Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 195, pp. 145- 150 ,(1995) , 10.1016/0921-5093(94)06513-6
H. Kakisawa, T. Mamiya, S. Q. Guo, W. H. Liu, S. J. Zhu, Y. Kagawa, Fabrication and mechanical properties of woven Al2O3 fibre – ZrO2 matrix minicomposite reinforced Al2O3 matrix composites by slurry infiltration – sintering process Materials Science and Technology. ,vol. 19, pp. 1681- 1687 ,(2003) , 10.1179/174328413X13789824293902
Mineo Mizuno, Shijie Zhu, Yasuo Nagano, Yoshihisa Sakaida, Yutaka Kagawa, Makoto Watanabe, Cyclic‐Fatigue Behavior of SiC/SiC Composites at Room and High Temperatures Journal of the American Ceramic Society. ,vol. 79, pp. 3065- 3077 ,(1996) , 10.1111/J.1151-2916.1996.TB08078.X
Wen-Chiang Tu, Fred F. Lange, Anthony G. Evans, Concept for a Damage-Tolerant Ceramic Composite with "Strong" Interfaces Journal of the American Ceramic Society. ,vol. 79, pp. 417- 424 ,(1996) , 10.1111/J.1151-2916.1996.TB08138.X
T. Ishikawa, S. Kajii, K. Matsunaga, T. Hogami, Y. Kohtoku, Structure and properties of Si-Ti-C-O fibre-bonded ceramic material Journal of Materials Science. ,vol. 30, pp. 6218- 6222 ,(1995) , 10.1007/BF00369669
T Mamiya, H Kakisawa, W.H Liu, S.J Zhu, Y Kagawa, Tensile damage evolution and notch sensitivity of Al2O3 fiber-ZrO2 matrix minicomposite-reinforced Al2O3 matrix composites Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 325, pp. 405- 413 ,(2002) , 10.1016/S0921-5093(01)01483-6
John W. Holmes, Influence of Stress Ratio on the Elevated‐Temperature Fatigue of a Silicon Carbide Fiber‐Reinforced Silicon Nitride Composite Journal of the American Ceramic Society. ,vol. 74, pp. 1639- 1645 ,(1991) , 10.1111/J.1151-2916.1991.TB07152.X