Vacuum Die Casting Process and Simulation for Manufacturing 0.8 mm-Thick Aluminum Plate with Four Maze Shapes
作者： Chul Kyu Jin , Chang Hyun Jang , Chung Gil Kang
DOI: 10.3390/MET5010192
关键词: Metallurgy 、 Ultimate tensile strength 、 Elongation 、 Alloy 、 Formability 、 Melt temperature 、 Materials science 、 Aluminium 、 Plunger 、 Die casting
摘要: … In size the product is 220 mm high, 220 mm wide, and 0.8 mm thick. Figure 1b shows the cross section of a gate. The cross-sectional area of the gate connected with the product is 147.2 …
mdpi.com
core.ac.uk 
sci-hub.se 参考文章(19)
Chang-Yeol Jeong, Jae-Ik Cho, Se-Weon Choi, Chang-Seog Kang, Sung-Kil Hong, Young-Chan Kim, Die Casting Mold Design of the Thin-walled Aluminum Case by Computational Solidification Simulation Journal of Materials Science & Technology. ,vol. 24, pp. 383- 388 ,(2009)
Anna Zovi, Federico Casarotto, SILAFONT-36, THE LOW IRON DUCTILE DIE CASTING ALLOY DEVELOPMENT AND APPLICATIONS La Metallurgia Italiana. ,(2007)
A. Zovi, F. Casarotto, D. Dragulin, R. Franke, PROGRESS IN DUCTILE ALUMINIUM HIGH PRESSURE DIE CASTING ALLOYS FOR THE AUTOMOTIVE INDUSTRY La Metallurgia Italiana. ,(2007)
Yucel Birol, Semi-solid processing of the primary aluminium die casting alloy A365 Journal of Alloys and Compounds. ,vol. 473, pp. 133- 138 ,(2009) , 10.1016/J.JALLCOM.2008.05.074
C. Dørum, H.I. Laukli, O.S. Hopperstad, M. Langseth, Structural behaviour of Al–Si die-castings: Experiments and numerical simulations European Journal of Mechanics A-solids. ,vol. 28, pp. 1- 13 ,(2009) , 10.1016/J.EUROMECHSOL.2008.03.004
Chul Kyu Jin, Chung Gil Kang, Fabrication process analysis and experimental verification for aluminum bipolar plates in fuel cells by vacuum die-casting Journal of Power Sources. ,vol. 196, pp. 8241- 8249 ,(2011) , 10.1016/J.JPOWSOUR.2011.05.073
Chul Kyu Jin, Chung Gil Kang, Fabrication by vacuum die casting and simulation of aluminum bipolar plates with micro-channels on both sides for proton exchange membrane (PEM) fuel cells International Journal of Hydrogen Energy. ,vol. 37, pp. 1661- 1676 ,(2012) , 10.1016/J.IJHYDENE.2011.10.050
E.S Kim, K.H Lee, Y.H Moon, A feasibility study of the partial squeeze and vacuum die casting process Journal of Materials Processing Technology. ,vol. 105, pp. 42- 48 ,(2000) , 10.1016/S0924-0136(00)00557-4
X.P. Niu, B.H. Hu, I. Pinwill, H. Li, Vacuum assisted high pressure die casting of aluminium alloys Journal of Materials Processing Technology. ,vol. 105, pp. 119- 127 ,(2000) , 10.1016/S0924-0136(00)00545-8
Z. Fan, X. Fang, S. Ji, Microstructure and mechanical properties of rheo-diecast (RDC) aluminium alloys Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 412, pp. 298- 306 ,(2005) , 10.1016/J.MSEA.2005.09.001