Simulation analysis of resin-based composites on temperature and degree of cure fields by thermoforming process considering the influence of temperature distribution inside the autoclave
作者： F. Sun , D. M. Liao , Z. C. Zhang , L. Cao , J. X. Zhou
DOI: 10.1179/1432891715Z.0000000001336
关键词:
摘要: AbstractThe curing process is critical in the production of composite materials. In this paper, a heat transfer and kinetics two-way coupling model reflecting resin-based was built. The degree temperature fields simulation programme using finite difference method independently also developed. With programme, numerical for flat plate conducted. distributions were obtained. results indicated that distribution plays an important role resin process. internal autoclave inhomogeneous. has non-linear relationship with gradient autoclave. Moreover, existence inside can have more significant influence at low than high one. This research provides certain basis optimising ...
sci-hub.se 参考文章(15)
C. Soutis, Fibre reinforced composites in aircraft construction Progress in Aerospace Sciences. ,vol. 41, pp. 143- 151 ,(2005) , 10.1016/J.PAEROSCI.2005.02.004
C.B. Xin, Y.Z. Gu, M. Li, J. Luo, Y.X. Li, Z.G. Zhang, Experimental and numerical study on the effect of rubber mold configuration on the compaction of composite angle laminates during autoclave processing Composites Part A: Applied Science and Manufacturing. ,vol. 42, pp. 1353- 1360 ,(2011) , 10.1016/J.COMPOSITESA.2011.05.018
Cédric Bernardin, Stefano Olla, Fourier's law for a microscopic model of heat conduction Journal of Statistical Physics. ,vol. 121, pp. 271- 289 ,(2005) , 10.1007/S10955-005-7578-9
J.L. Martín, A. Cadenato, J.M. Salla, Comparative studies on the non-isothermal DSC curing kinetics of an unsaturated polyester resin using free radicals and empirical models Thermochimica Acta. ,vol. 306, pp. 115- 126 ,(1997) , 10.1016/S0040-6031(97)00311-0
T BEHZAD, M SAIN, Finite element modeling of polymer curing in natural fiber reinforced composites Composites Science and Technology. ,vol. 67, pp. 1666- 1673 ,(2007) , 10.1016/J.COMPSCITECH.2006.06.021
Malak I. Naji, Suong V. Hoa, Curing of Thick Angle-Bend Thermoset Composite Part: Curing Process Modification for Uniform Thickness and Uniform Fiber Volume Fraction Distribution: Journal of Composite Materials. ,vol. 34, pp. 1710- 1755 ,(2000) , 10.1106/F97F-U8RD-QYN8-Q8JU
L.G. Zhao, N.A. Warrior, A.C. Long, A thermo-viscoelastic analysis of process-induced residual stress in fibre-reinforced polymer–matrix composites Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 452, pp. 483- 498 ,(2007) , 10.1016/J.MSEA.2006.10.060
Sung Yi, H.H. Hilton, M.F. Ahmad, A finite element approach for cure simulation of thermosetting matrix composites Computers & Structures. ,vol. 64, pp. 383- 388 ,(1997) , 10.1016/S0045-7949(96)00156-3
F.Y.C. Boey, W. Qiang, Experimental modeling of the cure kinetics of an epoxy-hexaanhydro-4-methylphthalicanhydride (MHHPA) system Polymer. ,vol. 41, pp. 2081- 2094 ,(2000) , 10.1016/S0032-3861(99)00409-7
R Andrews, M.C Weisenberger, Carbon nanotube polymer composites Current Opinion in Solid State & Materials Science. ,vol. 8, pp. 31- 37 ,(2004) , 10.1016/J.COSSMS.2003.10.006