Additive manufacturing of stellite 6 superalloy by direct laser metal deposition – Part 1: Effects of laser power and focal plane position
作者： Mahmoud Moradi , Ali Ashoori , Arman Hasani
DOI: 10.1016/J.OPTLASTEC.2020.106328
关键词:
摘要: … In this paper, the effect of the location of the focal plane position in powder stream and the laser power on the process of direct laser metal deposition additive manufacturing of stellite 6 …
harvard.edu
elsevier.com
sci-hub.st 参考文章(46)
Scott M. Thompson, Linkan Bian, Nima Shamsaei, Aref Yadollahi, An overview of Direct Laser Deposition for additive manufacturing; Part I: Transport phenomena, modeling and diagnostics Additive manufacturing. ,vol. 8, pp. 36- 62 ,(2015) , 10.1016/J.ADDMA.2015.07.001
Gianmario Scotti, Ville Matilainen, Petri Kanninen, Heidi Piili, Antti Salminen, Tanja Kallio, Sami Franssila, Laser additive manufacturing of stainless steel micro fuel cells Journal of Power Sources. ,vol. 272, pp. 356- 361 ,(2014) , 10.1016/J.JPOWSOUR.2014.08.096
T.E. Abioye, D.G. McCartney, A.T. Clare, Laser cladding of Inconel 625 wire for corrosion protection Journal of Materials Processing Technology. ,vol. 217, pp. 232- 240 ,(2015) , 10.1016/J.JMATPROTEC.2014.10.024
C.Y. Kong, R.J. Scudamore, J. Allen, High-rate laser metal deposition of Inconel 718 component using low heat-input approach Physics Procedia. ,vol. 5, pp. 379- 386 ,(2010) , 10.1016/J.PHPRO.2010.08.159
Ahmad Afiq Pauzi, Shuib Husin, Study on the Effect of Wear Resistant Materials Applications in Reducing Wear Damage of Gas Turbine Combustor Components Applied Mechanics and Materials. ,vol. 575, pp. 17- 21 ,(2014) , 10.4028/WWW.SCIENTIFIC.NET/AMM.575.17
Mahmoud Moradi, Majid Ghoreishi, Jan Frostevarg, Alexander F.H. Kaplan, An investigation on stability of laser hybrid arc welding Optics and Lasers in Engineering. ,vol. 51, pp. 481- 487 ,(2013) , 10.1016/J.OPTLASENG.2012.10.016
Pierre Muller, Pascal Mognol, Jean-Yves Hascoet, Modeling and control of a direct laser powder deposition process for Functionally Graded Materials (FGM) parts manufacturing Journal of Materials Processing Technology. ,vol. 213, pp. 685- 692 ,(2013) , 10.1016/J.JMATPROTEC.2012.11.020
Daniel Clark, Mark T. Whittaker, Martin R. Bache, Microstructural Characterization of a Prototype Titanium Alloy Structure Processed via Direct Laser Deposition (DLD) Metallurgical and Materials Transactions B-process Metallurgy and Materials Processing Science. ,vol. 43, pp. 388- 396 ,(2012) , 10.1007/S11663-011-9599-X
Singon Kang, Jae-Gil Jung, Mihyun Kang, Wanchuck Woo, Young-Kook Lee, The effects of grain size on yielding, strain hardening, and mechanical twinning in Fe–18Mn–0.6C–1.5Al twinning-induced plasticity steel Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 652, pp. 212- 220 ,(2016) , 10.1016/J.MSEA.2015.11.096
Nima Shamsaei, Aref Yadollahi, Linkan Bian, Scott M. Thompson, An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control Additive manufacturing. ,vol. 8, pp. 12- 35 ,(2015) , 10.1016/J.ADDMA.2015.07.002