Evaluation of the clean nano-cutting fluid by considering the tribological performance and cost parameters
作者： Enes Kilincarslan , Sena Kabave Kilincarslan , M Huseyin Cetin , None
DOI: 10.1016/J.TRIBOINT.2021.106916
关键词:
摘要: Abstract In this study, the tribological performance of cutting fluid developed with canola oil and nano-silver was investigated. Within scope AA7075-T6 material milled under conditions dry machining, boron oil, added oil. As a result experiments, surface roughness, forces, temperature, chip morphologies, tool wear were Nano-lubricant caused slight increase in machining but it provided high terms morphology wear. optimisation, determined to be optimum roughness temperature.
sci-hub.st 参考文章(58)
Nurettin Eltugral, Hamza Simsir, Selhan Karagoz, Preparation of nano-silver-supported activated carbon using different ligands Research on Chemical Intermediates. ,vol. 42, pp. 1663- 1676 ,(2016) , 10.1007/S11164-015-2110-6
B. Mohammad, K. A. Abou-El-Hossein, M. M. Noor, K. Kadirgama, Habeeb Al-Ani, Cutting force prediction model by FEA and RSM when machining Hastelloy C-22HS with 90° holder Journal of Scientific & Industrial Research. ,vol. 67, pp. 421- 427 ,(2008)
D. Cabaleiro, L. Colla, F. Agresti, L. Lugo, L. Fedele, Transport properties and heat transfer coefficients of ZnO/(ethylene glycol + water) nanofluids International Journal of Heat and Mass Transfer. ,vol. 89, pp. 433- 443 ,(2015) , 10.1016/J.IJHEATMASSTRANSFER.2015.05.067
Domnita Fratila, Sustainable Manufacturing Through Environmentally-Friendly Machining Green Manufacturing Processes and Systems. pp. 1- 21 ,(2013) , 10.1007/978-3-642-33792-5_1
Brian Boswell, Mohammad Nazrul Islam, The Challenge of Adopting Minimal Quantities of Lubrication for End Milling Aluminium IAENG Transactions on Engineering Technologies. pp. 713- 724 ,(2013) , 10.1007/978-94-007-6190-2_54
Robert Tibshirani, Trevor Hastie, Daniela Witten, Gareth James, An Introduction to Statistical Learning: With Applications in R ,(2013)
Sujan Debnath, Moola Mohan Reddy, Qua Sok Yi, Environmental friendly cutting fluids and cooling techniques in machining: a review Journal of Cleaner Production. ,vol. 83, pp. 33- 47 ,(2014) , 10.1016/J.JCLEPRO.2014.07.071
H. Safari, S. Sharif, S. Izman, H. Jafari, D. Kurniawan, Cutting Force and Surface Roughness Characterization in Cryogenic High-Speed End Milling of Ti–6Al-4V ELI Materials and Manufacturing Processes. ,vol. 29, pp. 350- 356 ,(2014) , 10.1080/10426914.2013.872257
Gaurav Bartarya, S.K. Choudhury, Effect of Cutting Parameters on Cutting Force and Surface Roughness During Finish Hard Turning AISI52100 Grade Steel Procedia CIRP. ,vol. 1, pp. 651- 656 ,(2012) , 10.1016/J.PROCIR.2012.05.016
G.V. Vinogradov, O.E. Morozova, A study of the wear of steel under heavy loads with lubricants containing sulphur-based additives Wear. ,vol. 3, pp. 297- 308 ,(1960) , 10.1016/0043-1648(60)90294-5