Effect of welding speed on microstructure and mechanical properties of titanium alloy/stainless steel lap joints during cold metal transfer method
作者： Gang Li , Shengyu Xu , Xiaofeng Lu , Xiaolei Zhu , Yupeng Guo
关键词:
摘要: Cold metal transfer (CMT) technique is developed for lap joining of titanium (Ti) alloy to stainless steel (SS) with CuSi3 filler wire. The effect welding speed on the microstructure and mechanical properties Ti/SS joints investigated. results indicate that wetting angle gradually increases weld width decreases increasing speed. It found many coarse phases in fusion zone are rich Ti, Fe Si etc, inferring as Fe–Si–Ti ternary phase and/or Fe2 Ti at low Many fine spherical particles considered iron-rich high transition layer exhibited Ti–Cu interface. With heat input, intermetallic becomes thicker. A variety brittle compounds (IMCs) identified joints. shear strength Two fracture modes occur Thicker reaction causes poor joint strength. Fe–Ti–Si within detrimental surface dominated by smooth tear pattern mode merely along
harvard.edu
sci-hub.st 参考文章(30)
Heng Zhang, Shengsun Hu, Zhijiang Wang, Ying Liang, The effect of welding speed on microstructures of cold metal transfer deposited AZ31 magnesium alloy clad Materials & Design. ,vol. 86, pp. 894- 901 ,(2015) , 10.1016/J.MATDES.2015.07.143
I. Tomashchuk, P. Sallamand, H. Andrzejewski, D. Grevey, The formation of intermetallics in dissimilar Ti6Al4V/copper/AISI 316 L electron beam and Nd:YAG laser joints Intermetallics. ,vol. 19, pp. 1466- 1473 ,(2011) , 10.1016/J.INTERMET.2011.05.016
R Cao, J H Sun, J H Chen, Mechanisms of joining aluminium A6061-T6 and titanium Ti–6Al–4V alloys by cold metal transfer technology Science and Technology of Welding and Joining. ,vol. 18, pp. 425- 433 ,(2013) , 10.1179/1362171813Y.0000000118
I. Magnabosco, P. Ferro, F. Bonollo, L. Arnberg, An investigation of fusion zone microstructures in electron beam welding of copper–stainless steel Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 424, pp. 163- 173 ,(2006) , 10.1016/J.MSEA.2006.03.096
R. Cao, Z. Feng, Q. Lin, J.H. Chen, Study on cold metal transfer welding–brazing of titanium to copper Materials & Design. ,vol. 56, pp. 165- 173 ,(2014) , 10.1016/J.MATDES.2013.10.044
C. P. Wang, Y. Hu, S. Y. Yang, Y. Lu, Q. W. Jiang, X. J. Liu, Experimental Investigation of Phase Equilibria in the Fe-Si-Zr Ternary System Journal of Phase Equilibria and Diffusion. ,vol. 34, pp. 277- 288 ,(2013) , 10.1007/S11669-013-0242-1
S. Zakipour, M. Samavatian, A. Halvaee, A. Amadeh, A. Khodabandeh, The effect of interlayer thickness on liquid state diffusion bonding behavior of dissimilar stainless steel 316/Ti-6Al-4V system Materials Letters. ,vol. 142, pp. 168- 171 ,(2015) , 10.1016/J.MATLET.2014.11.158
S. Kundu, G. Anand, S. Chatterjee, Diffusion Bonding of 17-4 Precipitation Hardening Stainless Steel to Ti Alloy With and Without Ni Alloy Interlayer: Interface Microstructure and Mechanical Properties Metallurgical and Materials Transactions A. ,vol. 44, pp. 2196- 2211 ,(2013) , 10.1007/S11661-012-1553-2
H.C. Dey, M. Ashfaq, A.K. Bhaduri, K. Prasad Rao, Joining of titanium to 304L stainless steel by friction welding Journal of Materials Processing Technology. ,vol. 209, pp. 5862- 5870 ,(2009) , 10.1016/J.JMATPROTEC.2009.06.018
M. Ghosh, S. Chatterjee, Effect of interface microstructure on the bond strength of the diffusion welded joints between titanium and stainless steel Materials Characterization. ,vol. 54, pp. 327- 337 ,(2005) , 10.1016/J.MATCHAR.2004.12.007