Investigation of Thrust Force and Delamination during Drilling of C/PPS
作者： Petr Masek , Petr Kolar , Pavel Zeman , Martin Vrabec
DOI: 10.21062/UJEP/X.2016/A/1213-2489/MT/16/6/1308
关键词:
摘要: Drill bits used for machining of composite materials can have different geometries and it is difficult to choose suitable geometry a specific type composite. Unsuitable drill bit leads bad surface quality. The objective this paper find the most thermoplastic C/PPS in terms quality magnitude thrust force under cutting conditions. Three were chosen experimental investigation. A significant influence point angle was identified. gradually decreased together with an increased rake edge lead better In addition, investigation conditions on forces performed. considerable feed observed comparison velocity. Information included help design more technology drilling composites.
sci-hub.st 参考文章(10)
Handbook of Composites Chapman & Hall. ,(1998) , 10.1007/978-1-4615-6389-1
Frédéric Lachaud, Robert Piquet, Francis Collombet, Laurent Surcin, Drilling of composite structures Composite Structures. ,vol. 52, pp. 511- 516 ,(2001) , 10.1016/S0263-8223(01)00040-X
H. Hocheng, H. Y. Puw, Machinability of fiber-reinforced thermoplastics in drilling Journal of Engineering Materials and Technology-transactions of The Asme. ,vol. 115, pp. 146- 149 ,(1993) , 10.1115/1.2902148
J.Paulo Davim, Pedro Reis, Drilling carbon fiber reinforced plastics manufactured by autoclave—experimental and statistical study Materials & Design. ,vol. 24, pp. 315- 324 ,(2003) , 10.1016/S0261-3069(03)00062-1
Pierre Rahmé, Yann Landon, Frédéric Lachaud, Robert Piquet, Pierre Lagarrigue, Analytical models of composite material drilling The International Journal of Advanced Manufacturing Technology. ,vol. 52, pp. 609- 617 ,(2011) , 10.1007/S00170-010-2773-5
F. Quadrini, E. A. Squeo, V. Tagliaferri, Machining of glass fiber reinforced polyamide Express Polymer Letters. ,vol. 1, pp. 810- 816 ,(2007) , 10.3144/EXPRESSPOLYMLETT.2007.112
Miroslav Müller, Petr Valášek, Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites Manufacturing Technology. ,vol. 12, pp. 55- 59 ,(2012) , 10.21062/UJEP/X.2012/A/1213-2489/MT/12/1/55
Vitalii Oleksandrovych Kolesnyk, Dmytro Volodymyrovych Kryvoruchko, Michal Hatala, Zuzana Hutyrova, Jan Duplak, Mohammed Alowa, Dusan Mital, None, The Effect of Cutting Temperature on Carbide Drilling Life in the Process of CFRP/Steel Stacks Drilling Manufacturing Technology. ,vol. 15, pp. 357- 362 ,(2015) , 10.21062/UJEP/X.2015/A/1213-2489/MT/15/3/357
Petr Valášek, Miroslav Müller, Influence of bonded abrasive particles size on wear of polymeric particle composites based on waste Manufacturing Technology. ,vol. 12, pp. 268- 272 ,(2012) , 10.21062/UJEP/X.2012/A/1213-2489/MT/12/2/268
Writers' Program of the Work Projects Administration in the State of Illinois, Drills CRC Press. ,(None) , 10.1201/B16729